Fisher and Paykel DE27CW1 User Guide - Page 28

Tighten Strain Relief screws.

Get Fisher and Paykel DE27CW1 PDF manuals and user guides View all Fisher and Paykel DE27CW1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

4-Wire Connections Use approved 4-wire Power Supply Cord or a 4-wire Cable for Direct Wiring as described on page 25. 1 Remove the terminal block cover plate. 2 Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet near the terminal block. Do not tighten strain relief screw until wiring connections are complete. Note: a strain relief must be used. 2 strain relief clamp sections strain relief screws 3 Remove center terminal block screw. 4 Remove appliance ground link by removing the ground connector screw (green screw). 3 4 Note: If the appliance is moved back to a 3-wire installation the ground link must be refitted. Remove link 5 Connect ground wire (green) of the power supply cord to the ground conductor green screw. Tighten screw. 6 Connect the neutral wire (white) of the power supply cord to the center terminal screw of the terminal block. Tighten screw. 7 Connect the red wire and black wire to the upper and lower terminal block screws marked with the letter L. Tighten screws. 7 6 5 7 8 Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and secure cover with securing screw. 9 Tighten Strain Relief screws. 8 9 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
28
4-Wire Connections
Use approved 4-wire Power Supply Cord or a 4-wire Cable for Direct Wiring as described
on page 25.
1
Remove the terminal block cover plate.
2
Insert the power supply cable with a UL listed strain relief through the hole provided in the cabinet
near the terminal block. Do not tighten strain relief screw until wiring connections are complete.
Note:
a strain relief must be used.
2
strain relief
clamp sections
strain relief
screws
3
Remove center terminal block screw.
4
Remove appliance ground link by removing the ground connector screw (green screw).
3
4
Note: If the appliance is moved back to a 3-wire
installation the ground link must be refitted.
Remove link
5
Connect ground wire (green) of the power supply cord to the ground conductor green screw.
Tighten screw.
6
Connect the neutral wire (white) of the power supply cord to the center terminal screw of the
terminal block. Tighten screw.
7
Connect the red wire and black wire to the upper and lower terminal block screws marked with the
letter L. Tighten screws.
7
6
5
7
8
Refit terminal block cover by inserting the two tabs first on the rear panel of the dryer and secure
cover with securing screw.
9
Tighten Strain Relief screws.
8
9