Fisher and Paykel DE27CW1 User Guide - Page 31

Completing the Connection

Get Fisher and Paykel DE27CW1 PDF manuals and user guides View all Fisher and Paykel DE27CW1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Connecting Gas to Your Dryer (Gas Models Only) US CA 4 A listed connector in compliance with ANSI Z21.24/CSA6.10 must be used to connect the dryer to the gas supply. 5 If flexible tubing is used, an elbow should be installed on the pipe at the back of the dryer for the flexible tube to be connected to. This will minimize damage to the tube when the dryer is moved back. Use a flexible tubing connection kit that has designed for use on a clothes dryer. This kit should have the unions necessary to join to the ends of the tubing. Be sure to follow all instructions supplied with the kit. 6 Copper tubing should not be used for Natural Gas and if used for LP Gas, it must be LP Gas compatible. 7 Disconnect and discard old flexible tubing. 8 The gas pipe that comes out of the rear of your dryer has on it a 3⁄8" NPT male thread. Remove the protective cap and apply sealing compound or tape to the thread. Thread sealant should be appropriate for the type of gas to be used. Apply thread sealant Remove cap 3⁄8" NPT pipe thread Elbow required for flexible tubing Completing the Connection 9 Use wrenches to tighten all joints but do not over tighten. 10 Open the gas supply valve and check all joints by brushing on a non-corrosive leak-detecting solution. Bubbling will indicate a leak. If any leaks are found, close the valve immediately and correct the leaks. Retest and repeat until no leaks are found. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
31
Connecting Gas to Your Dryer (Gas Models Only)
4
A listed connector in compliance with ANSI Z21.24/CSA6.10 must be used to connect the dryer
to the gas supply.
5
If flexible tubing is used, an elbow should be installed on the pipe at the back of the dryer for
the flexible tube to be connected to. This will minimize damage to the tube when the dryer is
moved back. Use a flexible tubing connection kit that has designed for use on a clothes dryer.
This kit should have the unions necessary to join to the ends of the tubing. Be sure to follow all
instructions supplied with the kit.
6
Copper tubing should not be used for Natural Gas and if used for LP Gas, it must be LP Gas
compatible.
7
Disconnect and discard old flexible tubing.
8
The gas pipe that comes out of the rear of your dryer has on it a ´⁄·” NPT male thread. Remove
the protective cap and apply sealing compound or tape to the thread. Thread sealant should be
appropriate for the type of gas to be used.
Apply thread
sealant
Remove cap
´⁄·” NPT pipe thread
Elbow required
for flexible tubing
Completing the Connection
9
Use wrenches to tighten all joints but do not over tighten.
10
Open the gas supply valve and check all joints by brushing on a non-corrosive leak-detecting
solution. Bubbling will indicate a leak. If any leaks are found, close the valve immediately and
correct the leaks. Retest and repeat until no leaks are found.
US
CA