Fisher and Paykel RF135BDRUX1 Joiner Kit Instructions (English) - Page 5

Step 6., Step 7., Step 8, Step 9

Page 5 highlights

Joiner Kit For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388, C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B Step 6. Locate the front upper bracket on the top surface of the two cabinets, taking care to line up the bosses on the Front Upper Bracket, with the six screw points. Note that the large centered rectangular section on the underside of the front upper bracket acts as a spacer between the two cabinets. Partially engage all of the screws (Type B, hex head, silver) prior to their final tightening. Step 8 To access the adjustable feet and to locate the front lower bracket, the joined cabinets must be tilted backwards approximately 60 degrees. This is a two person operation. The person at the rear of the cabinets must acknowledge that they have a secure grip of the cabinets prior to any work being undertaken by the second installer. Care must be taken not to damage either the cabinets/floor or the surrounding cupboards during this operation. Step 6 Step 7. Ensure the left cabinet is properly located within the rear bracket and that the cabinets are level. Secure the left cabinet to the rear bracket using 3 of the screws (Type A, self tapping, silver). Now replace the unit compartment cover at the back using a Phillips type screw driver (USA market only) Left hand side cabinet Right hand side cabinet 60 Step 8 Step 9 Remove the two Levelling Feet by rotating them anti-clockwise then remove the two bolts. Note: C450, E450, E440T, E442B, E521T and E522B may have an extra component as part of the levelling foot assembly, this being a stepped plastic washer. If this part is located, it is to be removed as it is not required to be used with this kit. Step 7 Step 9 Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7

Joiner Kit
For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,
C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B
Introduction Date: October 2007
Pt No.819265 INSTRUCTION KIT JOINER RF
5
Step 6.
Locate the front upper bracket on the top surface of the two
cabinets, taking care to line up the bosses on the Front Upper
Bracket, with the six screw points.
Note that the large centered rectangular section on the
underside of the front upper bracket acts as a spacer between
the two cabinets.
Partially engage all of the screws (Type B,
hex head, silver) prior to their final tightening.
Step 6
Step 7.
Ensure the left cabinet is properly located within the rear
bracket and that the cabinets are level. Secure the left cabinet
to the rear bracket using 3 of the screws (Type A, self tapping,
silver).
Now replace the unit compartment cover at the back using a
Phillips type screw driver (USA market only
)
Left hand
side cabinet
Right hand
side cabinet
Step 7
Step 8
To access the adjustable feet and to locate the front lower
bracket, the joined cabinets must be tilted backwards
approximately 60 degrees. This is a two person operation.
The person at the rear of the cabinets must acknowledge that
they have a secure grip of the cabinets prior to any work being
undertaken by the second installer.
Care must be taken not to damage either the cabinets/floor or
the surrounding cupboards during this operation.
60
Step 8
Step 9
Remove the two Levelling Feet by rotating them anti-clockwise
then remove the two bolts.
Note: C450, E450, E440T, E442B, E521T and E522B may
have an extra component as part of the levelling foot assembly,
this being a stepped plastic washer. If this part is located, it is to
be removed as it is not required to be used with this kit.
Step 9