Fluke Ti450 User Manual - Page 13

Battery, Two-Bay Battery Charger Base

Get Fluke Ti450 PDF manuals and user guides View all Fluke Ti450 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Thermal Imagers Before You Start Note [1] Fluke recommends the memory card that is supplied with the Imager or available from Fluke. Fluke does not warrant the use or reliability of aftermarket memory cards of different brands or capacities. [2] To request a printed manual, email Fluke at [email protected]. Specify the product name and language preference in the subject line. Battery Before you use the Imager for the first time, charge the battery for a minimum of two and one-half hours. The battery status shows on the five-segment charge indicator. W Warning To prevent personal injury, do not put battery cells and battery packs near heat or fire. Do not put in sunlight. Note New batteries are not fully charged. Two to ten charge/discharge cycles are necessary before the battery charges to its maximum capacity. To charge the battery, use one of the options that follow: Two-Bay Battery Charger Base 1. Connect the ac power supply to the ac wall outlet and connect the dc output to the charger base. 2. Put one or two smart batteries into bays of charger base. 3. Charge batteries until charge indicators show "full". 4. Remove smart batteries and disconnect the power supply when batteries are fully charged. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Thermal Imagers
Before You Start
9
Note
[1]
Fluke recommends the memory card that is supplied with the
Imager or available from Fluke. Fluke does not warrant the use or
reliability of aftermarket memory cards of different brands or
capacities.
[2]
To request a printed manual, email Fluke at
.
Specify the product name and language preference in the subject line.
Battery
Before you use the Imager for the first time, charge the battery for a minimum
of two and one-half hours. The battery status shows on the five-segment
charge indicator.
W
Warning
To prevent personal injury, do not put battery cells and battery
packs near heat or fire. Do not put in sunlight.
Note
New batteries are not fully charged. Two to ten charge/discharge
cycles are necessary before the battery charges to its maximum
capacity.
To charge the battery, use one of the options that follow:
Two-Bay Battery Charger Base
1.
Connect the ac power supply to the ac wall outlet and connect the dc
output to the charger base.
2.
Put one or two smart batteries into bays of charger base.
3.
Charge batteries until charge indicators show “full”.
4.
Remove smart batteries and disconnect the power supply when batteries
are fully charged.