Foxconn G31MXP-K English Manual. - Page 44

► IDE Primary Slave UDMA

Get Foxconn G31MXP-K PDF manuals and user guides View all Foxconn G31MXP-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

3 DMA transfers when the PCI bus is overclocked. Disabling DMA support will force the drive to use the slower PIO transfer mode. This may allow the drive to work properly with the higher PCI bus speed. ► On-Chip Primary PCI IDE Enable/Disable Primary IDE port. It also relates to the drives displayed on the IDE Channel 0 Master/Slave in "System Information" menu. ► IDE Primary Master PIO Specify a particular PIO mode (0,1,2,3,4) for legacy PIO operation or select Auto and let the system automatically detect it. ► IDE Primary Slave PIO Specify a particular PIO mode (0,1,2,3,4) for legacy PIO operation or select Auto and let the system automatically detect it. ► IDE Primary Master UDMA Disable UDMA operation or select Auto and let the system automatically detect it. ► IDE Primary Slave UDMA Disable UDMA operation or select Auto and let the system automatically detect it. **On-Chip Serial ATA Setting** ► SATA Controller [Disabled] : Disable SATA Controller. Only 2 IDE drives are available at PATA port. [Combined Mode] : SATA drives are acting as legacy IDE devices. Maximum there are four IDE drives. Two SATA drives are displayed as IDE Channel 0 Master/ Slave and two PATA drives are displayed as IDE Channel 1 Master/Slave in "System Information" menu. [Enhanced Mode] : Maximum of 4 IDE drives are supported. Two PATA drives are displayed as IDE Channel 0 Master/Slave, and two SATA drives are displayed as IDE Channel 2 Master/Slave in "�S�y�s�t�e�m��I�n�fo�r�m��a�t�io�n��" �m��e�n�u�. [SATA Only] : Two SATA drives are displayed as IDE Channel 0 Master/Slave in "�S�y�s�t�e�m� Information�" �m��e�n�u�. ► SATA Port Speed Settings When SATA is operating in [Enhanced Mode], you can select its speed to [Disabled], [Force GEN I] or [Force GEN II]. [Force GEN II] can get the best performance. ► PATA IDE Mode When SATA is operating in [Combined Mode], you can further select which one of PATA or SATA is functioning as the Primary IDE and which one is functioning as the Secondary. ► SATA Port When SATA is operating in [Combined Mode], you can refer to this display message to connect SATA drives with the corresponding SATA ports on the motherboard for correct operations. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
37
3
DMA transfers when the PCI bus is overclocked. Disabling DMA support will force the drive to
use the slower PIO transfer mode. This may allow the drive to work properly with the higher
PCI bus speed.
► On-Chip Primary PCI IDE
Enable/Disable Primary IDE port. It also relates to the drives displayed on the IDE Channel 0
Master/Slave in "System Information" menu.
► IDE Primary Master PIO
Specify a particular PIO mode (0,1,2,3,4) for legacy PIO operation or select Auto and let the
system automatically detect it.
► IDE Primary Slave PIO
Specify a particular PIO mode (0,1,2,3,4) for legacy PIO operation or select Auto and let the
system automatically detect it.
► IDE Primary Master UDMA
Disable UDMA operation or select Auto and let the system automatically detect it.
► IDE Primary Slave UDMA
Disable UDMA operation or select Auto and let the system automatically detect it.
**On-Chip Serial ATA Setting**
► SATA Controller
[Disabled] : Disable SATA Controller. Only 2 IDE drives are available at PATA port.
[Combined Mode] : SATA drives are acting as legacy IDE devices. Maximum there are four
IDE drives. Two SATA drives are displayed as IDE Channel 0 Master/
Slave and two PATA drives are displayed as IDE Channel 1 Master/Slave
in "System Information" menu.
[Enhanced Mode] : Maximum of 4 IDE drives are supported. Two PATA drives are displayed as
IDE Channel 0 Master/Slave, and two SATA drives are displayed as IDE
Channel 2 Master/Slave in "System Information" menu.
System Information" menu.
" menu.
[SATA Only] : Two SATA drives are displayed as IDE Channel 0 Master/Slave in "System
System
Information" menu.
" menu.
► SATA Port Speed Settings
When SATA is operating in [Enhanced Mode], you can select its speed to [Disabled], [Force
GEN I] or [Force GEN II]. [Force GEN II] can get the best performance.
► PATA IDE Mode
When SATA is operating in [Combined Mode], you can further select which one of PATA or
SATA is functioning as the Primary IDE and which one is functioning as the Secondary.
► SATA Port
When SATA is operating in [Combined Mode], you can refer to this display message to connect
SATA drives with the corresponding SATA ports on the motherboard for correct operations.