Frigidaire FAH106S1T Installation Instructions - Page 3

Sleeve, Brands

Get Frigidaire FAH106S1T - 10000 BTU Through-the-Wall Air Conditioner PDF manuals and user guides
UPC - 012505273063
View all Frigidaire FAH106S1T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Wall Sleeve Brands: Rear Louvers 3.s. 50° #1 Emerson 15" Deep 1. Redirect the louvers at the back of the wall sleeve as shown opposite. The use of pliers is recommended. Top View 2. Attach (1) 1 x 3/8" x 25" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 3. Attach (2) 1 1/2" x 3/8" x 14" seals to the left and right sides of the sleeve. 4. Cut (2) 1W x 3/8" x 25" long seals to 14" long each and attach to the vertical sections of the grille as shown. 5. Attach (2) 4 Y2" x 3 1/2" x 1 Y2" centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening. 6. Gently slide unit into sleeve. 7. Before sliding all-the-way back, remove 2nd screw from front on left side of unit. 8. Remove the plastic washer from the screw. 9. Screw and attach the other end of the ground wire to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 10. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. 11. Seal & Frame the unit as described on the last page of these instructions. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Wall
Sleeve
Brands:
3.s
.
Rear
Louvers
50°
Top
View
#1
Emerson
15"
Deep
1.
Redirect
the
louvers
at
th
e
back
of
the
wall
sleeve
as
shown
opposite.
The
use
of
pliers
is
recommended.
2.
Attach
(1)
1
x
3/8"
x
25"
long
seal
in
the
center
at
the
top
of
the
sleeve.
Remove
the
backing
paper
and
press
into
position.
3.
Attach
(2)
1
1/2"
x
3/8"
x
14"
seals
to
the
left
and
right
sides
of
the
sleeve.
4.
Cut
(2)
1W
x
3/8"
x
25"
long
seals
to
14"
long
each
and
attach
to
the
vertical
sections
of
th
e
grille
as
shown.
5.
Attach
(2)
4
Y2"
x
3
1
/
2
"
x
1
Y2"
centering/support
blocks
one
on
each
side
wall.
Place
in
center
of
side
wall
with
the
tapered
end
facing
the
opening.
6.
Gently
slide
unit
into
sleeve.
7.
Before
sliding
all
-the
-way
back,
remove
2nd
screw
from
front
on
left
side
of
unit.
8.
Remove
the
plastic
washer
from
the
screw.
9.
Screw
and
attach
the
other
end
of
the
ground
wire
to
the
unit
as
shown
in
picture.
Make
sure
that
the
toothed
washer
is
against
the
cabinet.
10.
Slide
the
unit
completely
to
the
rear
to
ensure
a
good
seal,
making
sure
the
ground
wire
does
not
become
tangled.
11.
Seal
&
Frame
the
unit
as
described
on
the
last
page
of
these
instructions.
3