Frigidaire FFEH3054US Installation Instructions - Page 2

Clearances and Dimensions - range

Get Frigidaire FFEH3054US PDF manuals and user guides View all Frigidaire FFEH3054US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

30" ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 1. Clearances and Dimensions a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location-Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. Front Typical cabinet installation view Side view Minimum to 1" wall on either side of range above 36" height. 30" Minimum 30" Minimum* Minimum to 18" cabinets on either side of range 13" Maximum depth for cabinets above range top. 25" Max. 29 7/8" 36 5/8" ± 1/4" Maximum 36" FRONT VIEW SIDE VIEW 30" Fig. 1 Minimum 0" clearance below cooking top and at rear of range 30" (762 mm) 30" (762 mm) Minimum Minimum to wall on either side of 1" range above (25 mm) 36'' (914 mm) height. *30" (762 mm) MINIMUM Minimum to 18" cabinets on 13" 330 mm (457 mm) either side of Maximum depth range. for cabinets CLEARANCE BETWabEovEe rNangeTtHop.E TOP OF THE COOKING SURFACE AND THE BOTT2O5" M OF AN UNPROTECTED WOOD OR METAL CABINE6T3;5OmmR 36" 24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR (914 mmM) ETAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" (0.4 mm) STAINLESS STEEL, 0.024" (0.6 mm) ALUMINUM OR 0.020" (0.5 m(m7632)0m"CmO) PPE0"R(0.m0m") c(le0aramncembe)loCw cLoEokAingRtoAp aNndCatEreaIrSof range. ROAVNEGRTAAEHLLLLE MINIMUM FOR THE REAR OF TH2E5- 3R/4A" NGE. FOLLOW DIMENSION REQUI(7R632E0m"Mm)ENTS(6P54RmOm)VIDED ABOVE DIMENTSOIOPNRS EVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD,AND INCORRECT COUNTERTOPAND CABINET CUTS. Centerline of range Fig. 2 26 6/8" Door 47" open BACK VIEW All dimensions for electrical outlet location are maximum. Dashed cubed area shows where the electrical outlet must be installed for flush to the wall installation. 11" (279 mm) 22" (559 mm) TO ELIMINAT4E8" THE RISK OF BURNS OR FIRE BY REACHING (OM12aV1x9imEmuRmm) HEATED STORAGE SPACE LOCATED SURFACE UNIT36S,1/C8"ABINET ABOVE THE S(9U14RmmF)A(3CmEm)UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD49T" HAT PROJECTS HORIZONTALLY A MINIMUM OF 5(1"24(51m2m7) Maximum mm) BEY2O9- N7/8D" THE BOTTOM OF THE CABINETSD.oor Open (759 mm) 6" (152 mm) 2-5/8" (67 mm) for models equipped with warmer drawers 3-1/2" (89 mm) for models equipped with storage drawers Wall Edge Fig. 3 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
2
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS
1. Clearances and Dimensions
a. Provide adequate clearances between the range and adjacent combustible surfaces.
b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor.
c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be
solid and level.
BACK
VIEW
1”
30” Minimum*
Minimum to
wall on either
side of range
above 36” height.
36”
18”
Minimum to
cabinets on
either side
of range
25” Max.
13”
Maximum depth
for cabinets
above range top.
0” clearance below cooking top and at rear of range
Typical cabinet installation
Front
view
Side
view
30”
Minimum
30”
Minimum
All dimensions for electrical outlet location
are maximum.
Dashed cubed area
shows where the electrical outlet must be
installed
for flush to the wall installation.
11”
(279 mm)
22”
(559 mm)
Wall
Edge
2-5/8” (67 mm) for models
equipped with warmer drawers
3-1/2” (89 mm) for models
equipped with storage drawers
6”
(152 mm)
*30" (762 mm) MINIMUM CLEARANCE BETWEEN THE
TOP OF THE COOKING SURFACE AND THE
BOTTOM
OF AN UNPROTECTED WOOD OR METAL CABINET; OR
24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR
METAL CABINET IS PROTECTED BY NOT LESS THAN
1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED
WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015"
(0.4 mm) STAINLESS STEEL, 0.024" (0.6 mm) ALUMINUM
OR 0.020" (0.5 mm) COPPER. 0" (0 mm) CLEARANCE IS
THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW
ALL DIMENSION REQUIREMENTS PROVIDED ABOVE
TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE
HAZARD, AND INCORRECT COUNTERTOP AND CABINET
CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY
REACHING OVER HEATED SURFACE UNITS, CABINET
STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS
SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE
PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING
A RANGE HOOD THAT PROJECTS HORIZONTALLY A
MINIMUM OF 5" (127 mm) BEYOND THE BOTTOM OF
THE CABINETS.
29
7
/
8
"
Maximum
36
5
/
8
"
±
1
/
4
"
26
6
/
8
"
47"
Door open
Fig. 2
Fig. 1
Fig. 3