Frigidaire FGB24S5DC Installation Instructions (All Languages) - Page 4

Cabinet Installation, Adjusting Oven Height - gas oven

Page 4 highlights

GAS WALL OVEN INSTALLATION INSTRUCTIONS 4. Adjusting Oven Height (Model with 1 ½ oven cavity only) Remove and lay aside the lower vent decorative trim that is taped to the side or to the top of the oven. The decorative trim will be fastened to the lower front of the oven after it has been installed in the cabinet. There is a 1 ½" height adjustment on models with extension panel (see figure 4). With this adjustment and a ½" trim overhang, a unit can be installed in existing openings 37 ½" to 39" high. Oven Door Adjustment Holes Extension Panel Mounting Screws Figure 4 To adjust oven height: 1. Lay oven on its back (see figure 5). 2. Remove the 6 screws that fasten the side extension panel to the bottom sides of the oven. 3. Move each panel down to the position that increases the oven height to fit your opening. Each position changes oven height approximately ½". 4. Line up the appropriate holes in the side extension panels and sides of the oven. Put the 6 screws back. 5. Proceed with oven installation. Return to upright position. Oven Bottom Figure 5 Extension Panel 5. Cabinet Installation A. Model With 1½ Oven Cavity Insert appliance into cutout. Use the 4 mounting screws provided to fasten the front frame of the appliance to the cabinet (steps 1 below). Keep the 2 decorative screws to fix the decorative trim to the cabinet (step 2 below). The mounting holes in the front frame of appliance may be used as a template to locate the appliance mounting screw holes on the cabinet. To fasten the appliance to the cabinet (figure 6): 1. Use 4 mounting screws supplied to secure the appliance to the cabinetry. 2 holes are located under the center vent trim on each side, the 2 other holes are visible when the drawer is opened. 2. Optional: Install the decorative trim under the appliance (as shown on figure 6) using the 2 decorative screws supplied with the appliance. Center Vent Trim Mounting Screws Mounting Screws Decorative Trim Decorative Screws Figure 6 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

GAS WALL OVEN INSTALLATION INSTRUCTIONS
4
5. Cabinet Installation
A.
Model With 1½ Oven Cavity
Insert appliance into cutout. Use the 4 mounting screws
provided to fasten the front frame of the appliance to
the cabinet (steps 1 below). Keep the 2 decorative
screws to fix the decorative trim to the cabinet (step 2
below). The mounting holes in the front frame of
appliance may be used as a template to locate the
appliance mounting screw holes on the cabinet.
To fasten the appliance to the cabinet (figure 6):
1. Use 4 mounting screws supplied to secure the
appliance to the cabinetry. 2 holes are located under
the center vent trim on each side, the 2 other holes
are visible when the drawer is opened.
2.
Optional:
Install the decorative trim under the
appliance (as shown on figure 6) using the 2
decorative screws supplied with the appliance.
4. Adjusting Oven Height
(Model with 1 ½ oven cavity only)
Remove and lay aside the lower vent decorative trim
that is taped to the side or to the top of the oven. The
decorative trim will be fastened to the lower front of the
oven after it has been installed in the cabinet.
There is a 1 ½" height adjustment on models with
extension panel (see figure 4). With this adjustment and
a ½" trim overhang, a unit can be installed in existing
openings 37 ½" to 39" high.
Figure 4
Oven Door
Oven Bottom
Extension Panel
Figure 5
To adjust oven height:
1. Lay oven on its back (see figure 5).
2. Remove the 6 screws that fasten the side extension
panel to the bottom sides of the oven.
3. Move each panel down to the position that increases
the oven height to fit your opening. Each position
changes oven height approximately ½".
4. Line up the appropriate holes in the side extension
panels and sides of the oven. Put the 6 screws back.
5. Proceed with oven installation. Return to upright
position.
Figure 6
Adjustment
Holes
Extension Panel
Mounting Screws
Center Vent Trim
Decorative Trim
Mounting Screws
Mounting
Screws
Decorative Screws