Frigidaire GAH12ER2T Installation Instructions - Page 8

Whirlpool

Get Frigidaire GAH12ER2T - GIBSON 12000BTU 115V 5.7A 9.0E3 SPD 4 WAY AIR DIRECTION PDF manuals and user guides
UPC - 012505272431
View all Frigidaire GAH12ER2T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Wall Sleeve Brands: #7 Whirlpool 23"Deep Rear Louvers 60° 1. Redirect the louvers at the back of the wall sleeve as shown in the 10" illustration. The use of pliers is recommended. 60° 9-1/2" Top View 2 3 2 ← 10"‹ → 4 2. Attach the (2) 41⁄2"x 31⁄2"x 11⁄2"foam blocks to the inside top and bottom of the wall sleeve with the slots 10"from the right side wall of the sleeve. Attach (2) Tapered Spacer Blocks behind rib on inside bottom of the wall sleeve as shown. Taper towards the rear of the sleeve. 17" 3/4" Tapered Spacer Block 3. Attach 1"x 3/4"x 14"long seal to the inside of the grille panel. 4. Install the 1/8"x 41⁄2"x 14"long plastic divider to the 131⁄4"long. Slide the plastic divider in the slots of the (2) foam blocks. ← 61⁄2"‹→ ← 61⁄2"‹→ ← 14 8"‹ → 5 5 5 5. Cut to fit (1) 11⁄2"x 11⁄2"x 261⁄2"long seals as shown. Attach (2) 11⁄2"x 11⁄2"x 14"long seals. Install the seals as shown. Seals should be flush with front side of 41⁄2"x 31⁄2"x 11⁄2"Foam Blocks which holds the plastic divider. 7. Install the 1"x 11⁄2'x 84"long stuffer seal between the wall sleeve and the unit. A flat bladed screwdriver or putty knife is recommended. 6. Install the new 7 unit into the wall 6 sleeve. Attach 7 the ground wire to the unit as shown. 9. Assemble and install the Trim Frame. (see Trim Frame) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
Wall Sleeve Brands:
Rear Louvers
60
°
10"
60
°
Top View
9-1/2"
#7 Whirlpool
23
"
Deep
1. Redirect the louvers at the back of the wall sleeve as shown in the
illustration. The use of pliers is recommended.
2. Attach the (2) 4
1
∕
2
"
x 3
1
∕
2
"
x 1
1
∕
2
"
foam blocks to the inside top and bot-
tom of the wall sleeve with the slots 10
"
from the right side wall of the
sleeve. Attach (2) Tapered Spacer Blocks behind rib on inside bottom
of the wall sleeve as shown. Taper towards the rear of the sleeve.
3. Attach 1
"
x 3/4
"
x 14
"
long seal to the inside of the grille panel.
4. Install the 1/8
"
x 4
1
∕
2
"
x 14
"
long plastic divider to the 13
1
∕
4
"
long.
Slide the plastic divider in the slots of the (2) foam blocks.
5. Cut to fit (1) 1
1
∕
2
"
x 1
1
∕
2
"
x 26
1
∕
2
"
long seals as shown.
Attach (2) 1
1
∕
2
"
x 1
1
∕
2
"
x 14
"
long seals. Install the seals as shown.
Seals should be flush with front side of 4
1
∕
2
"
x 3
1
∕
2
"
x 1
1
∕
2
"
Foam Blocks
which holds the plastic divider.
6. Install the new
unit into the wall
sleeve. Attach
the ground wire
to the unit as
shown.
8
3/4"
17"
Tapered Spacer Block
9. Assemble and install the Trim Frame. (see Trim Frame)
7. Install the 1
"
x 1
1
∕
2
'
x 84
"
long stuffer seal between the wall sleeve
and the unit. A flat bladed screwdriver or putty knife is recommended.
7
7
2
3
2
4
5
5
5
←
10
"‹
→
←
14
"‹
→
←
8
"‹
→
←
6
1
∕
2
"‹
→
←
6
1
∕
2
"‹
→
6