Fujitsu MAS3735NC Manual/User Guide - Page 77

Setting Terminals, CAUTION, Setting terminals location on NP models only

Get Fujitsu MAS3735NC - Enterprise - Hard Drive PDF manuals and user guides
UPC - 000004309314
View all Fujitsu MAS3735NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

5.3 Setting Terminals A user sets up the following terminals and SCSI terminating resistor before installing the IDD in the system as required. • Setting terminal: CN1 (NC model), CN2 (NP model) Figure 5.2 shows the location of setting terminal (NP model only. For NC model, see Figure 4.13 because the setting terminal is included in SCSI connector CN1.). Figure 5.3 shows the allocation and default settings (NP model only. For allocation of NC model, see Table B.). CAUTION Data loss 1. The user must not change the setting of terminals not described in this section. Do not change setting status set at factory shipment. 2. Do not change the setting of terminals except following setting pins during the power is turned on. • Write protect: CN2 9-10 (NP model only) 3. To short the setting terminal, use the short plug attached when the device is shipped from the factory. Pin 2 Pin 24 CN2 Pin 1 Pin 23 Figure 5.2 Setting terminals location (on NP models only) C141-E185 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
C141-E185
5-5
5.3
Setting Terminals
A user sets up the following terminals and SCSI terminating resistor before installing the IDD in
the system as required.
•
Setting terminal:
CN1 (NC model), CN2 (NP model)
Figure 5.2 shows the location of setting terminal (NP model only.
For NC model, see Figure 4.13
because the setting terminal is included in SCSI connector CN1.).
Figure 5.3 shows the allocation
and default settings (NP model only.
For allocation of NC model, see Table B.).
CAUTION
Data loss
1.
The user must not change the setting of terminals not described in this
section.
Do not change setting status set at factory shipment.
2.
Do not change the setting of terminals except following setting pins
during the power is turned on.
•
Write protect:
CN2
9-10 (NP model only)
3.
To short the setting terminal, use the short plug attached when the device
is shipped from the factory.
Pin 1
Pin 23
Pin 24
CN
2
Pin 2
Figure 5.2
Setting terminals location (on NP models only)