Garmin Fishfinder 400C Owner's Manual - Page 34

Alarms and Messages, Can't Read Voltages That High, Limited to Top of Range

Get Garmin Fishfinder 400C PDF manuals and user guides
UPC - 753759063801
View all Garmin Fishfinder 400C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Appendix Alarms and Messages The Fishfinder 400C uses an on-screen message system to alert you to unit operating characteristics. When a message appears, press SELECT to acknowledge the message and return to the screen you were viewing. Battery Alarm-battery voltage has fallen below the value entered in the Battery Alarm setup. Battery Voltage Is Too High-too much input voltage; the unit shuts off in 10 seconds. Decrease the input voltage to 35 Volts or less. Boat Is Not Moving Fast Enough to Calibrate-the boat is not moving fast enough for the speed wheel to provide a valid speed. Can't Read Voltages That High, Limited to Top of Range-the voltage value in the Battery Alarm setup is higher than the unit can read. Can't Read Voltages That Low, Limited to Bottom of Range-the voltage value in the Battery Alarm setup is lower than the voltage where the unit automatically turns off. Deep Water Alarm-the Deep Water Alarm depth has been reached. Drift Alarm-the depth has changed by the amount of the Drift Alarm value. Fish Alarm-an icon appears and a beep sounds (if enabled) when a fish is detected. This alarm does not show a message banner. Shallow Water Alarm-the Shallow Water Alarm depth has been reached. Simulating Operation-the unit is in Simulator Mode. Sonar Failed, Unit Needs Repair-there is an internal problem with the fishfinder. Contact your dealer or Garmin Product Support to have the unit serviced. Transducer Disconnected, Sonar Turned Off-there is not a transducer attached, bad cable/transducer, or the transducer cable was disconnected. If the transducer cable is removed while the unit is on, reconnect and cycle power. Water Speed Sensor Is Not Working-the speed sensor is not detected. Check the connections. Entering (Leaving) target water temperature-the target water temperature is 2° F (1.1° C) above or below the temperature specified by the Water Temperature Alarm. These messages appear when you enter or leave that zone. 28 Fishfinder 400C Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
28
Fishfinder 400C Owner’s Manual
A
PPENDIX
Alarms and Messages
The Fishfinder 400C uses an on-screen message system to alert you
to unit operating characteristics. When a message appears, press
SELECT
to acknowledge the message and return to the screen you
were viewing.
Battery Alarm
—battery voltage has fallen below the value entered
in the Battery Alarm setup.
Battery Voltage Is Too High
—too much input voltage; the unit
shuts off in 10 seconds. Decrease the input voltage to 35 Volts or
less.
Boat Is Not Moving Fast Enough to Calibrate
—the boat is not
moving fast enough for the speed wheel to provide a valid speed.
Can’t Read Voltages That High, Limited to Top of Range
—the
voltage value in the Battery Alarm setup is higher than the unit can
read.
Can’t Read Voltages That Low, Limited to Bottom of
Range
—the voltage value in the Battery Alarm setup is lower than
the voltage where the unit automatically turns off.
Deep Water Alarm
—the Deep Water Alarm depth has been
reached.
Drift Alarm
—the depth has changed by the amount of the Drift
Alarm value.
Fish Alarm
—an icon appears and a beep sounds (if enabled) when a
fish is detected. This alarm does not show a message banner.
Shallow Water Alarm
—the Shallow Water Alarm depth has been
reached.
Simulating Operation
—the unit is in Simulator Mode.
Sonar Failed, Unit Needs Repair
—there is an internal problem
with the fishfinder. Contact your dealer or Garmin Product Support
to have the unit serviced.
Transducer Disconnected, Sonar Turned Off
—there is not a
transducer attached, bad cable/transducer, or the transducer cable
was disconnected. If the transducer cable is removed while the unit
is on, reconnect and cycle power.
Water Speed Sensor Is Not Working
—the speed sensor is not
detected. Check the connections.
Entering (Leaving) target water temperature—
the target water
temperature is 2° F (1.1° C) above or below the temperature
specified by the Water Temperature Alarm. These messages appear
when you enter or leave that zone.