Garmin GPS 24xd Installation Instructions - Page 5
Cleaning the Outer Casing, Appendix
View all Garmin GPS 24xd manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
2 Set the display to view heading data from the antenna. 3 Disconnect the antenna from the NMEA 2000 network or turn off the power to the NMEA 2000 network. 4 Wait while the boat becomes level and stationary. 5 Turn on power to the antenna, and wait until the heading data appears on the display . NMEA 2000 drop cable length Temperature range Case material Water rating Compass-safe distance Power input source Max. input current Typical input current NMEA 2000 LEN @ 9 Vdc NMEA 2000 draw 19 ft., 8 in. (6 m) From -30° to 80°C (from -22° to 176°F) Fully gasketed, high-impact plastic alloy IEC 60529 IPX6 and IPX71 12.7 mm (0.5 in.) 9 to 16 Vdc, unregulated 200 mA @ 12 Vdc 150 mA @ 12 Vdc 3 150 mA 6 Within three minutes, complete two full, slow, tight circles , taking care to keep the boat as steady and level as possible. Heading data disappears to indicate that the antenna has detected the start of the procedure . You may receive an error message that the heading was lost. You can ignore this message. 7 Bring the boat to a complete stop , and remain stationary for two minutes. After two minutes, the heading data reappears with a fixed value of 123 degrees to indicate heading will be disabled on the next power cycle. NOTE: If the magnetic heading is displayed, the fixed value is 123 degrees. If the true heading is displayed, the fixed value may deviate because of corrections from magnetic variation. 8 Disconnect the antenna from the NMEA 2000 network or turn off the power to the NMEA 2000 network. 9 Turn on power to the antenna, and verify that heading has been disabled . Antenna Configuration Your antenna is pre-configured, but you may customize your antenna configuration as needed. From the NMEA 2000 device list, select the GPS 24xd, and select Review. Auto Locate: Allows you to clear existing satellite data and force the device to acquire new data. Factory Defaults: Allows you to reset the antenna settings to the factory default value. You will lose all custom configuration settings. Cleaning the Outer Casing NOTICE Avoid chemical cleaners and solvents that can damage plastic components. 1 Clean the outer casing of the device using a cloth dampened with a mild detergent solution. 2 Wipe the device dry. Appendix Software Update You must update the Garmin chartplotter software when you install this device. For instructions on updating the software, see your chartplotter owner's manual at support.garmin.com. Specifications Dimensions (diameter x height) 319/32 × 115/16 in. (91.6 × 49.5 mm) Weight 201 g (7.1 oz.) NMEA 2000 PGN Information Transmit 059392 060928 126208 126464 126992 126996 127250 127258 129025 129026 129029 129539 129540 ISO acknowledgment ISO address claimed Request group function Transmit and receive PGN list group function System time Product information Vessel heading Magnetic variation Position: Rapid update COG and SOG: Rapid update GNSS position data GNSS DOPs GNSS Sats in view Receive 059392 059904 060928 126208 ISO acknowledgment ISO request ISO address claimed Request group function Declaration of Conformity Hereby, Garmin declares that this product is in compliance with the Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.garmin.com/compliance. Innovation, Science and Economic Development Canada Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min, and is protected against powerful jets of water. For more information, go to www.garmin.com/waterrating. 5