Garmin GPSMAP 3010c Owners Manual - Page 73

NMEA Interface, To activate the NMEA data, Advanced NMEA Output Setup

Get Garmin GPSMAP 3010c - Marine GPS Receiver PDF manuals and user guides
UPC - 753759045548
View all Garmin GPSMAP 3010c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

NMEA Interface If you are going to use the GPSMAP 3006C/3010C with a NMEA device (such as a VHF radio or autopilot), the unit needs to be set to input/output NMEA data. See the GPSMAP 3006C/3010C & GPS 17 Installation Instructions for information on wiring and NMEA data. To activate the NMEA data: 1. Highlight the Port 1 or Port 2 field, and press ENTER. 2. Highlight NMEA In/NMEA Out, and press ENTER. When transferring data between two Garmin units, always set one to Host and use the other unit to send or request the data. Main Menu > System Tab Use the Advanced NMEA Setup Page to turn the GPS status (GSA, GSV), Waypoint/Route (WPL, RTE), and the Garmin proprietary sentences on or off. Check any other equipment's owners manual to see what sentences are required to be enabled for functionality. Lat/Lon Minutes Precision allows you to adjust the number of digits to the right of the decimal point for transmission of NMEA Output, either 2, 3, or 4 digits. Use the Waypoint ID setting to output the waypoint identifiers as names or numbers. Main Menu Advanced NMEA Output Setup The GPSMAP 3006C/3010C NMEA data transmission can be customized to change the precision of the Lat/Lon minutes, set up the waypoint IDs, and keep the output rate at two seconds. If the unit is set up to output all of the available NMEA sentences, the output rate may exceed two seconds. GPSMAP 3006C/3010C Owner's Manual Advanced NMEA Setup Page To change the advanced NMEA settings: 1. Press the NMEA Setup soft key to open the Advanced NMEA Setup Page. 2. To change, enable, or disable NMEA output sentences, highlight the sentence, and press ENTER to select or clear the check box. Only selected sentences are output. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
GPSMAP 3006C/3010C Owner’s Manual
6³
M
AIN
M
ENU
>
S
YSTEM
T
AB
M
AIN
M
ENU
NMEA Interface
If you are going to use the GPSMAP 3006C/3010C with a NMEA device (such
as a VHF radio or autopilot), the unit needs to be set to input/output NMEA
data. See the GPSMAP 3006C/3010C
& GPS 17 Installation Instructions for
information on wiring and NMEA data.
To activate the NMEA data:
1.
Highlight the
Port 1
or
Port 2
field, and press
ENTER
.
2.
Highlight
NMEA In/NMEA Out
, and press
ENTER
.
When transferring data between two Garmin units, always set one to
Host
and
use the other unit to send or request the data.
Advanced NMEA Output Setup
The GPSMAP 3006C/3010C NMEA data transmission can be customized to
change the precision of the
Lat/Lon
minutes, set up the waypoint IDs, and keep
the output rate at two seconds. If the unit is set up to output all of the available
NMEA sentences, the output rate may exceed two seconds.
Use the Advanced NMEA Setup Page to turn the GPS status (GSA, GSV),
Waypoint/Route (WPL, RTE), and the Garmin proprietary sentences on or off.
Check any other equipment’s owners manual to see what sentences are required
to be enabled for functionality.
Lat/Lon Minutes Precision
allows you to adjust the number of digits to the right
of the decimal point for transmission of NMEA Output, either 2, 3, or 4 digits.
Use the
Waypoint ID
setting to output the waypoint identifiers as names or
numbers.
Advanced NMEA Setup Page
To change the advanced NMEA settings:
1.
Press the
NMEA Setup
soft key to open the Advanced NMEA Setup
Page.
2.
To change, enable, or disable NMEA output sentences, highlight the
sentence, and press
ENTER
to select or clear the check box. Only
selected sentences are output.