Garmin STRIKER 5cv Owner s Manual PDF - Page 12
Alarms Settings, Unit Settings, Navigation Settings, Restoring the Factory Default Settings - gps
View all Garmin STRIKER 5cv manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
number to display water depth. Enter a 0 in this value to display depth below keel and depth below transducer. 2 Select Settings > My Vessel > Keel Offset. 3 Select or based on the location of the transducer. 4 Enter the distance measured in step 1. Setting the Water Temperature Offset You can set the temperature offset to compensate for the temperature reading from a temperature-capable sensor. 1 Measure the water temperature using the temperature- capable transducer that is connected to the device. 2 Measure the water temperature using a different thermometer or temperature sensor that is known to be accurate. 3 Subtract the water temperature measured in step 1 from the water temperature measured in step 2. This is the temperature offset. Enter this value in step 5 as a positive number if the sensor connected to the device measures the water temperature as being colder than it actually is. Enter this value in step 5 as a negative number if the sensor connected to the device measures the water temperature as being warmer than it actually is. 4 Select Settings > My Vessel > Temp. Offset. 5 Use the arrow keys to enter water temperature offset measured in step 3. Alarms Settings Navigation Alarms Select Settings > Alarms > Navigation. Arrival: Sets an alarm to sound when you are within a specified distance or time from a turn or a destination. Anchor Drag: Sets an alarm to sound when you exceed a specified drift distance while anchored. Off Course: Sets an alarm to sound when you are off course by a specified distance. System Alarms Alarm Clock: Sets an alarm clock. Device Voltage: Sets an alarm to sound when the battery reaches a specified low voltage. GPS Accuracy: Sets an alarm to sound when the GPS location accuracy falls outside the user-defined value. Sonar Alarms Select Settings > Alarms > Sonar. Shallow Water: Sounds when the water depth is shallower than the specified depth. Deep Water: Sounds when the water depth is deeper than the specified depth. Water Temp.: Sounds when the water temperature varies more than ± 2°F (± 1.1°C). Alarm settings are saved when the device is turned off. NOTE: You must connect the device to a temperaturecapable transducer to use this alarm. Fish: Sets an alarm to sound when the device detects a suspended target. • sets the alarm to sound when fish of all sizes are detected. • sets the alarm to sound only when medium or large fish are detected. • sets the alarm to sound only when large fish are detected. Unit Settings Select Settings > Units. System Units: Sets the unit format for the device. Variance: Sets the magnetic declination, the angle between magnetic north and true north, for your present location. North Reference: Sets the direction references used in calculating heading information. True sets geographic north as the north reference. Grid sets grid north as the north reference (000º). Magnetic sets the magnetic north as the north reference. Position Format: Sets the position format in which a given location reading appears. Do not change this setting unless you are using a map or chart that specifies a different position format. Map Datum: Sets the coordinate system on which the map is structured. Do not change this setting unless you are using a map or chart that specifies a different map datum. Time Format: Sets a 12-hour, 24-hour, or UTC time format. Time Zone: Sets the time zone. Daylight Savings Time: Sets daylight savings time to Off or On. Navigation Settings NOTE: Some settings and options require additional hardware. Select Settings > Navigation. Route Labels: Sets the type of labels shown with route turns on the map. Turn Transition Activ.: Sets the turn transition to be calculated based on time or distance. Turn Transition Time: Sets how many minutes before the turn that you transition to it as the next leg, when Time is selected for the Turn Transition Activ. setting. Turn Transition Dist.: Sets how far before the turn that you transition to it as the next leg, when Distance is selected for the Turn Transition Activ. setting. Route Start: Selects a starting point for route navigation. You can select Boat to start navigation from the current vessel location, or Waypoints to start from the first waypoint on the route. Restoring the Factory Default Settings NOTE: This deletes all settings information you have entered. 1 Select > System > System Information > Factory Settings. 2 Select an option. 8 Device Configuration