Gastroback 41000 User Manual - Page 11

Assembling the blender jug, WARNING, IMPORTANT, ATTENTION, Do

Get Gastroback 41000 PDF manuals and user guides View all Gastroback 41000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Assembling the blender jug Ensure that the blender jug and all units are clean before you assemble the appliance. A 1. To reassemble the blender jug, replace the silicon seal onto the blade assembly housing (picture A). Ensure the sealing ring is in proper position. The sealing ring has to be clean and show no crustifications, crinkles, cracks or look porous. 2. Hold on to the blade assembly housing with your right hand and with your left hand hold on to the handle of the blender jug. Upturn the blender jug and insert the blade assembly housing into the jug base (picture B and C). Twist the Blade Removal System anticlockwise until firmly locked into position. B WARNING: The blades are very sharp. Pay attention handling it and if possible only hold on to the blade assembly housing. NOTE: The blade assembly housing has two small guiding pins that fit in the matching gaps of the base of the blender jug. The blade assembly housing is in the right position if it seats solidly onto the base of the blender jug and when you can twist it anticlockwise. NOTE: Ensure the blade assembly housing is securely locked C onto the jug base. The blade assembly housing and the sealing ring should be properly connected to seal the bottom of the blender jug. Otherwise ingredients will run right into the motorblock. IMPORTANT: Do not tighten them with force or too tight to avoid damaging the appliance or the sealing ring. Ensure the sealing ring is in position and did not fall into the blender jug when assembling. ATTENTION: Ensure the blender jug is leak-proof before putting the blender jug on the motorblock. Always wipe off spilled liquids immediately. Never let any liquids run into the motorblock or underneath it to avoid electric shock. When liquids are spilled on the motor housing, immediately unplug the appliance and dry the motor housing to avoid risk of electric shock or fire. Do not attempt to operate the appliance, when liquids are on or in the motor housing. ATTENTION: Never place the holder or the blade only on the motorblock. Never touch the drive gear when the plug is connected to the power outlet. Without the blade assembly housing the bottom of the blender jug is open. Spilled liquids might run right into the motor. ATTENTION: When liquids are spilled on the motor housing, immediately unplug the appliance and dry the motor housing to avoid risk of electric shock or fire. Do not attempt to operate the appliance, when liquids are on or in the motor housing. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Assembling the blender jug
Ensure that the blender jug and all units are clean before you
assemble the appliance.
1.
To reassemble the blender jug, replace the silicon seal onto the
blade assembly housing (picture A). Ensure the sealing ring is
in proper position. The sealing ring has to be clean and show
no crustifications, crinkles, cracks or look porous.
2.
Hold on to the blade assembly housing with your right hand
and with your left hand hold on to the handle of the blender
jug. Upturn the blender jug and insert the blade assembly housing into the jug base
(picture B and C). Twist the Blade Removal System anticlockwise
until firmly locked into position.
WARNING:
The blades are very sharp. Pay attention handling
it and if possible only hold on to the blade assembly housing.
NOTE:
The blade assembly housing has two small guiding pins
that fit in the matching gaps of the base of the blender jug. The
blade assembly housing is in the right position if it seats solidly onto
the base of the blender jug and when you can twist it anticlockwise.
NOTE:
Ensure the blade assembly housing is securely locked
onto the jug base.
The blade assembly housing and the sealing ring should be
properly connected to seal the bottom of the blender jug.
Otherwise
ingredients
will
run
right
into
the
motorblock.
IMPORTANT:
Do not tighten them with force or too tight to
avoid damaging the appliance or the sealing ring. Ensure the
sealing ring is in position and did not fall into the blender jug
when assembling.
ATTENTION:
Ensure the blender jug is leak-proof before putting the blender jug on
the motorblock. Always wipe off spilled liquids immediately. Never let any liquids run
into the motorblock or underneath it to avoid electric shock. When liquids are spilled
on the motor housing, immediately unplug the appliance and dry the motor housing to
avoid risk of electric shock or fire.
Do not
attempt to operate the appliance, when
liquids are on or in the motor housing.
ATTENTION:
Never place the holder or the blade only on the motorblock. Never
touch the drive gear when the plug is connected to the power outlet. Without the
blade assembly housing the bottom of the blender jug is open. Spilled liquids might
run right into the motor.
ATTENTION:
When liquids are spilled on the motor housing, immediately unplug
the appliance and dry the motor housing to avoid risk of electric shock or fire.
Do
not
attempt to operate the appliance, when liquids are on or in the motor housing.
11
A
C
B