GE AV447FBS Installation Instructions - Page 5

Replaceable charcoal filter NOTE: DO NOT rinse, or put charcoal filters in an automatic dishwasher. &KDUFRDO)LOWHU³5HFLUFXODWLQJ,QVWDOODWLRQV2QO\ The charcoal filter cannot be cleaned. It must be replaced. Order filter no. WB02X10700. Replacement filters can be ordered from your GE supplier. If the hood is not vented to the outside, the air will be recirculated through a disposable charcoal filter that helps remove smoke and odors. The charcoal filter should be replaced after 6 to 12 months (depending on hood usage). To remove: Pull down on the center of the front edge of the filter. The filter will then slip out of the retaining tabs on the back. To replace: Slip the back edge of the filter into the retaining tabs and push the front edge up until it snaps into place. Stainless Steel Surfaces (on some models) Do not use a steel-wool pad; it will scratch the surface. To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the grain. Follow the cleaner instructions for cleaning the stainless steel surface. To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, please call our toll-free number: National Parts Center 800.626.2002 GEApplianceParts.com Painted Surfaces (on some models) Do not use steel-wool pads or other abrasive cleaners. They will scratch the surface. Clean grease-laden surfaces of the hood frequently. To clean the hood surface, use a hot, damp cloth with a mild detergent suitable for painted surfaces. About one tablespoon of ammonia may be added to the water. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth. NOTE: When cleaning, take care not to come in contact with filters and other nonenameled surfaces. CAUTION: When cleaning the hood surfaces, be certain that you do not touch the light bulb with moist hands or cloth. A warm or hot light bulb may break if touched with a moist surface. Always let the light bulb cool completely before cleaning around it. Light cover When using an energy saving bulb in your GE hood make sure you use either: GE Long Life Energy Smart™ Spiral® T2 Product Code: 85383 Description: FLE13HT2/2/SW/CD or GE Long Life Energy Smart™ A17 Product Code: 47486 Description: FLE11/2/A17XL/CD Available at www.gelighting.com Hood Light CAUTION: Let the light bulb cool completely before removing. A warm or hot bulb may break if touched with a moist cloth or hand. Remove the bulb and replace it with a type A15 incandescent light bulb with an ordinary screw base, not more than 60 Watts, or a type A17 or T2 Compact Fluorescent (CFL) light bulb with an ordinary screw base, not more than 13 Watts. NOTE: Use only incandescent bulbs in models RN328, JN327 and JV338. IMPORTANT: For installation, handling and disposal precautions, refer to the fluorescent bulb packaging literature. To remove the light cover (on some models): ‡ 3UHVVWKHVLGHVZLWKWZRILQJHUVXQWLOWKH side prongs are released. ‡ /LIWWKHOLJKWFRYHUDQGVOLGHLWWRZDUG\RX in one motion. To replace the light cover: ‡ ,QVHUWWKHSURQJORFDWHGDWWKHHQGRIWKH cover into the top opening. ‡ *HQWO\SXVKWKHFRYHUXSDQGSUHVVWKH sides to fit the side prongs into the side openings. ‡ 5HOHDVHDQGWKHFRYHUZLOOORFNLQSRVLWLRQ 5