GE GSC22QGT Use and Care Manual - Page 24

Removing and replacing the doors., Removing the Doors

Get GE GSC22QGT - Appliances 22.1 cu. Ft. Refrigerator PDF manuals and user guides View all GE GSC22QGT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Removing and replacing the doors. When installing or moving the refrigerator, the doors may need to be removed in order to fit the refrigerator through a doorway. Removing the Doors Make sure the doors are closed and the refrigerator is unplugged. Disconnect water line and wiring harness. Near the lower hinge on the freezer side, push in on the collars at each end of the coupling, and pull the water line tubing from the coupling. Also, disconnect wiring harness. Pull the water line and the harness through the lower rail. Remove the hinge covers and the hinges. In order to access the hinges, the hinge covers need to be removed. Remove the cover by grasping it on the sides, near the back of the cover. Push back on the cover and lift up at the back, then the front. NOTE: DO NOT use a screwdriver to remove the cover. BE CAREFUL not to break the rear retaining tab on the hinge cover. Remove the hinges using a Torx T-20. Remove the doors. Carefully rotate the door to 90°. Guiding the disconnected water line and wiring harness, lift the door straight up. NOTE: Not lifting the door straight up may damage the bottom hinge. Place doors on a protected surface. NOTE: Be careful not to pinch the water tubing and the wire harness at the bottom of the door. NOTE: Do not allow the connector to contact the floor. Hard contact can damage the connector. See "Replacing the Doors." Wire Harness Collars Hinge Cover Replacing the Doors Place doors on bottom hinges. With the door at 90°, lower the door straight down onto the bottom hinge. Carefully close the door. NOTE: Not lowering the door straight down onto the bottom hinge may damage the hinge. NOTE: Do not allow the connector to contact the floor. Hard contact can damage the connector. Replace top hinges and hinge covers. Reinstall the top hinges using a Torx T-20. Replace the hinge covers. If the doors are not level, adjust the bottom right hinge with a 7/16″ open ended wrench. Reconnect water line and wiring harness. Insert water tubing back into coupling, making sure the tubing is pushed far enough into the coupling so that you no longer see the mark on the tubing. Reconnect the wiring harness. Turn on the water supply and plug the refrigerator back in. 90 Door Hinge Pin Connector 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
Removing and replacing the doors.
When installing or moving the refrigerator, the doors may need to be removed in order to fit the refrigerator through
a doorway.
Removing the Doors
Make sure the doors are closed and the refrigerator is
unplugged.
Disconnect water line and wiring harness.
Near the lower hinge on the freezer side, push in on the
collars at each end of the coupling, and pull the water
line tubing from the coupling. Also, disconnect wiring
harness. Pull the water line and the harness through the
lower rail.
Remove the hinge covers and the hinges.
In order to access the hinges, the hinge covers need to be
removed. Remove the cover by grasping it on the sides,
near the back of the cover. Push back on the cover and
lift up at the back, then the front.
NOTE:
DO NOT use a screwdriver to remove the cover. BE CAREFUL
not to break the rear retaining tab on the hinge cover. Remove the
hinges using a Torx T-20.
Remove the doors.
Carefully rotate the door to 90°
. Guiding the disconnected
water line and wiring harness, lift the door straight up.
NOTE:
Not lifting the door straight up may damage the bottom hinge.
Place doors on a protected surface.
NOTE:
Be careful not to pinch the water tubing and the wire harness
at the bottom of the door.
NOTE:
Do not allow the connector to contact the floor. Hard contact
can damage the connector. See “Replacing the Doors.”
Replacing the Doors
Place doors on bottom hinges.
With the door at 90°
, lower the door straight down onto
the bottom hinge. Carefully close the door.
NOTE:
Not lowering the door straight down onto the bottom hinge
may damage the hinge.
NOTE:
Do not allow the connector to contact the floor. Hard contact
can damage the connector.
Replace top hinges and hinge covers.
Reinstall the top hinges using a Torx T-20. Replace the
hinge covers. If the doors are not level, adjust the bottom
right hinge with a 7/16
″
open ended wrench.
Reconnect water line and wiring harness.
Insert water tubing back into coupling, making sure the
tubing is pushed far enough into the coupling so that you
no longer see the mark on the tubing. Reconnect the
wiring harness.
Turn on the water supply and plug the refrigerator back in.
90
Hinge Cover
Door
Hinge Pin
Wire Harness
Collars
Connector
24