Gigabyte GA-990FXA-UD3 R5 Manual - Page 65

Configuring Marvell® 88SE9172 SATA Controller, 88SE9172 SATA Controller

Get Gigabyte GA-990FXA-UD3 R5 PDF manuals and user guides View all Gigabyte GA-990FXA-UD3 R5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

3-2 Configuring Marvell® 88SE9172 SATA Controller A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. The Marvell® 88SE9172 SATA controller controls the eSATA connectors on the back panel. Then connect the power connector from your power supply to the hard drive. B. Configuring SATA controller and RAID mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Step 1: Turn on your computer and press to enter BIOS Setup during the POST. To create RAID, go to Peripherals\Marvell SATA Controller Configuration and make sure GSATA Controller is set to RAID Mode. (Figure 1). Figure 1 Step 2: Save changes and exit BIOS Setup. The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. - 65 - Configuring SATA Hard Drive(s)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
- 65 -
Configuring SATA Hard Drive(s)
3-2
Configuring Marvell
®
88SE9172 SATA Controller
A. Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA
port on the motherboard. The Marvell
®
88SE9172 SATA controller controls the eSATA connectors on the back
panel. Then connect the power connector from your power supply to the hard drive.
B. Configuring SATA controller and RAID mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST. To create RAID, go to
Peripherals\Marvell SATA Controller Configuration
and make sure
GSATA Controller
is set to
RAID Mode
.
(Figure 1).
Figure 1
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
Step 2:
Save changes and exit BIOS Setup.