Gigabyte GA-G41M-Combo Manual - Page 28

IDE Channel 0, 2, 3 Master/Slave, Drive - no display

Page 28 highlights

2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2010 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Mon, May 10 2010 22:31:24 Item Help Menu Level  } IDE Channel 0 Master } IDE Channel 0 Slave } IDE Channel 2 Master } IDE Channel 2 Slave } IDE Channel 3 Master } IDE Channel 3 Slave [None] [None] [None] [None] [None] [None] Drive A Floppy 3 Mode Support [1.44M, 3.5"] [Disabled] Halt On [All, But Keyboard] Base Memory Extended Memory Total Memory 640K 2012M 2014M Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults Date (mm:dd:yy) Sets the system date. Time (hh:mm:ss) Sets the system time. IDE Channel 0, 2, 3 Master/Slave IDE HDD Auto-Detection, IDE Auto-Detection Press to autodetect the parameters of the IDE/SATA device on this channel. IDE Channel 0 Master/Slave, Extended IDE Drive Configure your IDE/SATA devices by using one of the three methods below: • Auto Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default) • None If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. • Manual Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. (For IDE Channel 0 Master/Slave only.) Access Mode Sets the hard drive access mode. (Default: Auto) The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Cylinder Number of cylinders. Head Number of heads. Precomp Write precompensation cylinder. Landing Zone Landing zone. Sector Number of sectors. Drive A Allows you to select the type of floppy disk drive installed in your system. If you do not install a floppy disk drive, set this item to None. Options are: None, 360K/5.25", 1.2M/5.25", 720K/3.5", 1.44M/3.5", 2.88M/3.5". BIOS Setup - 28 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

BIOS Setup
- 28 -
Date (mm:dd:yy)
Sets the system date.
Time (hh:mm:ss)
Sets the system time.
IDE Channel 0, 2, 3 Master/Slave
IDE HDD Auto-Detection, IDE Auto-Detection
Press <Enter> to autodetect the parameters of the IDE/SATA device on this channel.
IDE Channel 0 Master/Slave, Extended IDE Drive
Configure your IDE/SATA devices by using one of the three methods below:
Auto
Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default)
None
If no IDE/SATA devices are used, set this item to
None
so the system will skip the
detection of the device during the POST for faster system startup.
Manual
Allows you to manually enter the specifications of the hard drive when the hard drive
access mode is set to
CHS
. (For
IDE Channel 0 Master/Slave
only.)
Access Mode
Sets the hard drive access mode. (Default: Auto)
The following fields display your hard drive specifications. If you wish to enter the parameters manually,
refer to the information on the hard drive.
Capacity
Approximate capacity of the currently installed hard drive.
Cylinder
Number of cylinders.
Head
Number of heads.
Precomp
Write precompensation cylinder.
Landing Zone
Landing zone.
Sector
Number of sectors.
Drive A
Allows you to select the type of floppy disk drive installed in your system. If you do not install a floppy
disk drive, set this item to
None
. Options are: None, 360K/5.25", 1.2M/5.25", 720K/3.5", 1.44M/3.5",
2.88M/3.5".
2-4
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2010 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Mon,
May
10
2010
Time (hh:mm:ss)
22:31:24
IDE Channel 0 Master
[None]
IDE Channel 0 Slave
[None]
IDE Channel 2 Master
[None]
IDE Channel 2 Slave
[None]
IDE Channel 3 Master
[None]
IDE Channel 3 Slave
[None]
Drive A
[1.44M, 3.5"]
Floppy 3 Mode Support
[Disabled]
Halt On
[All, But Keyboard]
Base Memory
640K
Extended Memory
2012M
Total Memory
2014M

: Move
Enter: Select
+/-/PU/PD: Value
F10: Save
ESC: Exit
F1: General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7: Optimized Defaults
Item Help
Menu Level