Gigabyte MD70-HB1 Manual - Page 38

SATA_DOM0/SATA_DOM0 SATA port 0 and port 1 DOM Jumpers, CLR_CMOS Clearing CMOS Jumper

Get Gigabyte MD70-HB1 PDF manuals and user guides View all Gigabyte MD70-HB1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

1) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds. 1 1-2 Close: Normal operation (Default setting) 1 2-3 Close: Clear CMOS data. • Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. • After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard. 2/3) SATA_DOM0/SATA_DOM0 (SATA port 0 and port 1 DOM Jumpers) CAUTION! • If the SATA DOM power is supplied by the motherboard, set the jumper to pin 1-2. • If the SATA DOM power is supplied by external power, set the jumper to pin 2-3. • If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage. Please refer to the pin definition table in the following. 1 For SATA_DOM0 Pin No. Definition 1 P5V 2 SATA0 Pin7 3 GND SATA_DOM1 SATA_DOM0 For SATA_DOM0 Pin No. Definition 1 P5V 1 2 SATA1 Pin7 3 GND Hardware Installation - 38 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Hardware Installation
- 38 -
2/3) SATA_DOM0/SATA_DOM0 (SATA port 0 and port 1 DOM Jumpers)
CAUTION!
•
If the SATA DOM power is supplied by the motherboard, set the jumper to pin 1-2.
•
If the SATA DOM power is supplied by external power, set the jumper to pin 2-3.
•
If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed
and set to
2-3 pins
(Default setting), in order to reduce any risk of hard disk damage.
Please refer to the pin definition table in the following.
Pin No.
Definition
1
P5V
2
SATA0 Pin7
3
GND
For SATA_DOM0
Pin No.
Definition
1
P5V
2
SATA1 Pin7
3
GND
For SATA_DOM0
1
1
1
1
1)
CLR_CMOS (Clearing CMOS Jumper)
Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset
the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to
temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few
seconds.
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data.
•
Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS
values.
•
After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from
the jumper. Failure to do so may cause damage to the motherboard.
SATA_DOM0
SATA_DOM1