Haier HLPW028AXW Installation and User Manual - Page 8

Installation Requirements - washer

Get Haier HLPW028AXW PDF manuals and user guides View all Haier HLPW028AXW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

INSTALLATION REQUIREMENTS TOOLS NEEDED • Pliers • Wrench • Flat-blade Screwdriver • Measuring Tape • Carpenter's Level • Phillips Screwdriver PARTS SUPPLIED • Drain Hose Clamp • Drain Hose Hook • Drain Hose • Water Hoses (2) (flat washers pre-installed) • User Manual • Bottom Cover (with screw) LOCATION REQUIREMENTS • The washer must be installed on a solid floor to minimize vibration during the spin cycle. A concrete floor is best. • The floor should be level with maximum slope of 1" (25 mm) under entire washer. • A suitable location is protected from direct sunlight and heat sources such as radiators, baseboard heaters, or cooking appliances. • Do not install on carpeting. • The location must have a grounded electrical outlet located within 4 ft. (1.2 m) of power cord on the back of the washer. • Hot and cold water faucets must be present within 3 ft. (0.9 m) of the hot and cold connections on the washer. • A water heater must supply hot water with a temperature of at least 120°F (49°C). • The water pressure should be between 20 and 100 psi (138 and 690 kPa). IMPORTANT: Do not install or operate the washer where it will be exposed to temperatures below 32°F (0°C). Water remaining in the washer will freeze and cause damage to the washer. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
6
INSTALLATION REQUIREMENTS
TOOLS NEEDED
•
Pliers
•
Wrench
•
Flat-blade Screwdriver
•
Measuring Tape
•
Carpenter’s Level
•
Phillips Screwdriver
PARTS SUPPLIED
•
Drain Hose Clamp
•
Drain Hose Hook
•
Drain Hose
•
Water Hoses (2)
(flat washers pre-installed)
•
User Manual
•
Bottom Cover
(with screw)
LOCATION REQUIREMENTS
•
The washer must be installed on a solid floor to minimize vibration during the
spin cycle. A concrete floor is best.
•
The floor should be level with maximum slope of 1" (25 mm) under entire washer.
•
A suitable location is protected from direct sunlight and heat sources such as
radiators, baseboard heaters, or cooking appliances.
•
Do not install on carpeting.
•
The location must have a grounded electrical outlet located within 4 ft. (1.2 m) of
power cord on the back of the washer.
•
Hot and cold water faucets must be present within 3 ft. (0.9 m) of the hot and
cold connections on the washer.
•
A water heater must supply hot water with a temperature of at least 120°F
(49°C).
•
The water pressure should be between 20 and 100 psi (138 and 690 kPa).
IMPORTANT:
Do not install or operate the washer where it will be exposed to
temperatures below 32°F (0°C). Water remaining in the washer will freeze and cause
damage to the washer.