Haier HLTD600AEW User Manual - Page 21

Step 2 - Connect To A Gas Supply Line, Gas Dryer Only

Get Haier HLTD600AEW PDF manuals and user guides View all Haier HLTD600AEW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

STEP 2 - CONNECT TO A GAS SUPPLY LINE (GAS DRYER ONLY) NOTE: Do not connect the dryer to an LP gas line without first converting the dryer with a conversion kit. An LP conversion kit must be installed by a qualified technician. NOTE: Apply a pipe-joint compound that that is resistant to the action of LP gas to all males threads. Do not use plumber's tape. 1. Turn the gas supply off by moving the shutoff valve to the closed position. a Closed Valve A b Open Valve B 2. Disconnect and discard old flexible gas connector. Replace with a new CSA(AGA) approved flexible gas connector. 3. Remove the shipping cap from the gas inlet pipe at the rear of the dryer. 4. Connect a ⅜" NPT elbow to the gas inlet pipe on the dryer. Then connect a flare adapter to the elbow. IMPORTANT: Use a pipe wrench to keep the dryer gas inlet pipe from twisting. a Gas Inlet Pipe on the Dryer b ⅜" NPT Elbow A C c ⅜" NPT Flare Adapter B 5. Connect the dryer to the gas supply line with a flexible gas connector. a Flexible Gas Connector A 6. Tighten the flexible gas connector using two adjustable wrenches. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
19
STEP 2 - CONNECT TO A GAS SUPPLY LINE
(GAS DRYER ONLY)
NOTE:
Do not connect the dryer to an LP gas line without first converting the
dryer with a conversion kit. An LP conversion kit must be installed by a qualified
technician.
NOTE:
Apply a pipe-joint compound that that is resistant to the action of LP gas to
all males threads. Do not use plumber’s tape.
1.
Turn the gas supply off by moving the shutoff valve to the closed position.
a
Closed Valve
b
Open Valve
A
B
2.
Disconnect and discard old flexible gas connector. Replace with a new CSA(AGA)
approved flexible gas connector.
3.
Remove the shipping cap from the gas inlet pipe at the rear of the dryer.
4.
Connect a ⅜" NPT elbow to the gas inlet pipe on the dryer. Then connect a flare
adapter to the elbow.
IMPORTANT:
Use a pipe wrench to keep the dryer gas inlet pipe from twisting.
a
Gas Inlet Pipe on
the Dryer
b
⅜" NPT Elbow
c
⅜" NPT Flare Adapter
A
B
C
5.
Connect the dryer to the gas supply line with a flexible gas connector.
a
Flexible Gas Connector
A
6.
Tighten the flexible gas connector using two adjustable wrenches.