Haier HSU-09H03 User Manual - Page 6

Operation iFP Operation FRESH Operation The movement of people in the room can be sensed, which can improve the air adjustment efficiency. Exhaust the vitiated air from the room, and inhale fresh air. iFP AM 1 Press iFP button" iFP " is displayed on the remote controller and " " is displayed on the display board,unit will run in iFP mode. 2 Every time the button is pressed, display changes as follows: Remote controller: BLANK Detect the location of the human body,adjust the wind AM swing, blow the location where the body is. Press FRESH button" " is displayed on the remote controller and " " is displayed on the display board,and the change-for-fresh-air function operation begins. For twice press , the display " "disappears and the change-for-fresh-air function operation is canceled. note：If the unit didn't install change-for-fresh-air electrical engine, change-for-fresh-air function is not available. Detect the location of the human body,adjust the wind swing, avoid the location where the body is. About change-for-fresh-air function SMART When several people are located at different positions, or one person is moving in different areas, no matter whether the wind is blowing or not, the wind will automatically swing and blow to multi areas, the wind direction adjustment will be delayed, it cannot be deflected suddenly while detecting. In iFP,FOLLOW and EVADE operation mode, Press" " buttonđthe unit will not operate" " mode ,Press" the operation stops. "buttonđ The human body sensor is used to detect if the infrared ray is changing. It may be inaccurate in the following conditions: The human body keeps still (when reading or watching TV etc.) or is blocked by barriers like screen, cabinet or glass. The person is wearing very thick clothes or the person is lying or sleeping. A pet is moving frequently, or the wind is blowing the curtains, or something in the room is swinging frequently. SMART After the change-for-fresh-air function is initiated, the outside air can enter the indoors through the change-for-fresh-air tube thereby keeping the indoor air fresh. Setting the change-for-fresh-air function under the shutdown status, press the fresh air key and the remote controller displays the on status of air flow, low wind, and change-for-fresh-air functions, and now can set the timing open, timing close and time control switch. The dual fresh air has a memory function, which can be cancelled by pressing the key one time. Under the smart mode, after the machine has been running for a while, the dual fresh air function will be started automatically, it will be automatically stopped after continuously running for a while. ECO Operation Emergency operation and test operation Automatic adjusting with the environmental temperature, running with power saving. ECO AM SMART Press ECONOMY button" ECO " is displayed on the remote controllerđ unit will run in ECONOMY operation. Press ECONOMY button For twice press, ECONOMY disappears,the operation stops. The power saving function only works under the cooling, heating or dehumidifying mode, after the power saving function is set, press the sharp, mute, sleep, or smart key to exit the power saving function. After the power saving is set, the host machine will automatically adjust the setting temperature, and automatically control the switch of the compressor, which may be inconsistent with the user's setting. The power saving function is more effective after the air conditioning has been running for a long time (more than 2 hours) Emergency Operation: Pi Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed,the" Pi "sound is heard once, which means the start of this operation. In this operation, the system automatically selects the operation modes,cooling or fan or heat,according to the room temperature. Room Operation Designated Timer temperature mode temperature mode Air flow ABOVE 23OC COOLING 26OC NO AUTOMATIC BELOW 23OC HEAT 23OC NO AUTOMATIC (Cooling only uint） Room temperature Operation Designated mode temperature BELOW 23OC FAN 26OC It is not possible to operate in dry mode. Timer mode NO Air flow AUTOMATIC Test operation: Test operation switch is the same as emergency switch. Use this switch in the test operation when the room temperature is below 16oC, do not use it in the normal operation. Continue to press the test operation Pi Pi switch for more than 5 seconds. After you hear the "Pi" sound twice,release your finger from the switch: the cooling operation starts with the air flow speed "Hi". 5