Haier HWM75-0528A User Manual - Page 7
Usage the drain hose
View all Haier HWM75-0528A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
b Steps of using the operation buttons and description of the steps Program STANDARD SOAK HEAVY GENTLE SAVE COTTON SINGLE WASH RINSE SPIN SINGLE SPIN TUB CLEAN AIR DRY INDICATION OF PROCESS (NO CHOOSING) SOAK WASH RINSE SPIN START PAUSE TIME REMAINED(MINUTES) FLASH LIGHT RESERVE(HOURS LATER) PROGRAM/RESERVE WATER LEVEL POWER ON/OFF Digital display Fuzzy logic control 10 water level selection 1.Push "POWER"button to switch on the power 2.Push "PROGRAM/RESERVE" button to select suitable automatic program POWER ON/OFF PROGRAM/RESERVE After the power is switched on, "standard" is automatically set. To select other full-auto program, please push the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE button" on Page 11.E.g For instance:select "SAVE" program for small quantity of laundries with light soil. 12 Program select The display of digitron Program Application The running process (the digitron displays the running process) 01 STANDARD Common washing WASH( ) RINSE( ) SPIN( ) 02 SOAK HEAVY Washing for coverlet bigger laundries SOAK( ) WASH( ) RINSE( ) SPIN( ) 03 GENTLE Washing the woollen silk textiles WASH( ) RINSE( ) SPIN( ) 04 SAVE Washing for normal laundries WASH( ) RINSE( ) SPIN( ) 05 COTTON Washing the cotton textiles 06 SINGLE WASH Reusing the washing detergent WASH( ) RINSE( ) SPIN( ) WASH( ) 07 RINSE SPIN Washing the cloth washedby hand (first draining, then spinning) RINSE( ) SPIN( ) 08 SINGLE SPIN Only spinning the cloth wetor washed by hand (first draining, then spinning) SPIN( ) 09 TUB CLEAN The spinning time is thesame to the single spin, but spinning in lower SPIN( ) 10 AIR DRY Avoid growing mildew on the outer tub and the inner tub SPIN( ) How to change the direction of the drain hose 1.Dismantle the rear cover of the washing machine. 2.Put down the drain hose .Take off the drain hose frame as indicated in Figure 1.Take the drain hose into the cabinet ,then nip the drain fixing clamp to make it deviated from the clip,the other hand is used to put down the drain bushing,as indicated in Figure 2,3. 3.Dismantle the drain outlet protecting cover at the other side, (the way is the same as the drain bushing),then install the drain bushing, as indicated in Figure 4. 4.Extend the drain hose from the other side. Fix the drain hose with drain hose frame onto the cabinet, as indicated in Figure 5. Drain outlet protecting cover Drain hose Figure 1 Drain hose support Cabinet Inner Outer Push Drain bushing Figure 2 Drain bushing Figure 4 Figure 5 Drain bushing 5.Install the drain outlet protecting cover to the other side, as indicated in Figure 6 Drain hose fixing clamp Push Take down Figure 3 Figure 6 Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose with our company serviceman . Usage the drain hose The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way. 2.Do not step on or press the drain hose. 4.If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. 3. If the drain hose is too long, cut it at mid point. To make 5.If the extra hose is too long, cut it either at A or at B. smooth drainage, cut the front end of the hose slantingly. 5