Haier HWM75-0528A User Manual - Page 8
Connection between the water inlet hose jointer and the water faucet, Confirm the water faucet
View all Haier HWM75-0528A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Install the water inlet hose Confirm the water faucet Water faucet,suitable Water faucet,not suitable Outlet end surface It is required that the front end shall be longer than 10mm. The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage. Connection between the water inlet hose jointer and the water faucet 1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1. 2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.) Lock level water inlet hose water inlet hose jointer Slider Screw knife Figure 1 Screw Sign plate Figure 2 Bushing Figure 3 3.Fasten the four screws evenly. See to Figure 4. 4.Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5. remark: Before installation, the threading is 4mmabove the upper surface of the nut. After installation, the threading is 2mm above the upper surface of the nut. See to figure 6. About 4mm before twisting About less than 2mm after twisting Figure 4 Screw nut Figure 5 Figure 6 Reserve,Process,remain time digitron It displays "--" during detecting. It displays remained reserve time (hour). It displays total remained time (min). If the total time exceeds 99 minutes, it uses "A" on tens digit to represent100 minutes, and uses "b" to represent 110 minutes.E.g. "A3" represents 103 minutes. It displays abnormal symbol in abnormal situation. (See to Page15) "Power" button Push the "power" button to switch on the power. Under power-on mode, push it to switch off the power. Push the "power" button to switch on the power. If the "start/pause" button is not pushed, the machine will switch off the power automatically after 5 minutes. (MINUTES) FLASH LIGHT (HOURS LATER) PROGRAM/RESERVE WATER LEVEL POWER ON/OFF Digital display Fuzzy logic control 10 water level selection PROGRAM/RESERVE button Push down the program/ reserve button. You can select one program of ten which is standard,soak heavy, gentle,save,cotton, single wash,rinse spin,single spin,tub clean, air dry; Push the"program/ reserve" button to set the reserve wash program morethan two seconds continuously; When the "reserve" function is activated, the indicator light of the program you have set will be off. The "reserve (hour)" and "time remain" indicator lights will be on; During reserve procedure, push the "reserve" button to display the reserve mode.To change the running program or cancel the reserve setting, you need to switch off the power and make new selection; WATER LEVEL button The washing machine can detect the laundries automatically. After detection,it will set the water level to suitable value among 4, 6, 8,and 10 automatically. You can also set water level by yourself. After the machine is started, it will not set water level automatically. You shall push thestart/pause button to make new setting. If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 . If save program is selected, it will display water level 2 . When water level 2 is reached in water filling, it will perform washing while filling water.When water level 3 is reached, it will change to normal washing. During operation of wash and rinse program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water. The water level decided may be different from actual value because of the different moisture level of the laundries. Attention As selecting the waterlevel 1,3,5,7,9;the light is flashing; As selecting thewater level 2,4,6,8,10;the light is lighting;