Haier QDP555SBNTS Installation Instructions - Page 12

Connect Drain Line, Cont., Step 17

Get Haier QDP555SBNTS PDF manuals and user guides View all Haier QDP555SBNTS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Dishwasher Installation STEP 17 CONNECT DRAIN LINE The molded end of the drain hose will fit 5/8" through 1" diameter inlet ports on the air gap, waste tee or disposer. • Determine size of inlet port. • Cut drain hose connector on the marked line, if required, to fit the inlet port. Cutting Line STEP 17 C(COONNNTE.)CT DRAIN LINE • Connect drain line to air gap, waste tee or disposer using the previously determined method. Secure hose with a screw-type clamp. Method 1 - Air gap with waste tee or disposer 1" 5/8" IMPORTANT: Do not cut corrugated Figure Z portion of hose • If a longer drain hose is required, replace the provided user bag drain hose with GE Appliances 1871 Art4 service part WD24X10065, a 12' long hose which can be connected directly to the drain loop already attached to the unit (see Step 7). If service part hose is not available, an additional hose with coupler, ID of 5/8" or 7/8" and no longer than 66", may be attached to the provided user bag drain hose. Secure the connection with hose clamp (obtain locally) to the provided user bag drain hose. Waste Tee Installation Disposer Installation Figure AB Method 2 - "High drain loop" with waste tee or disposer With this method you will need the drain hose hanger set aside in Step 1. Fasten drain hose to underside of countertop with the provided hanger. Drain Hose Hanger Drain Hose Hanger Figure AA Hose Coupler Hose Clamp Clamp NOTES: • DRAIN CONNECTION HEIGHT IS NOT TO EXCEED 72" ABOVE BOTTOM OF DISHWASHER. • TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 12 FEET FOR PROPER DRAIN OPERATION. 32" 18" Min. Min. 32" 18" Min. Min. Waste Tee Installation Disposer Installation Figure AC IMPORTANT - When connecting drain line to dreismpoovsee0dr,5. cDDhIe-S1cHk2Wt9oA4bSBeHsEuRreWthILaLt dNraO0inT5pDDluR-g1A2hINa9sI4FbCePeLnUG IS LEFT IN PLACE. Remove Drain Plug Tip: Avoid unnecessary service call charges for a no drain complaint. Make sure excess drain hose has been pulled through the cabinet opening. This will prevent excess hose in the dishwasher cavity from becoming kinked or crushed by the dishwasher. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
CONNECT DRAIN LINE
(CONT.)
• Connect drain line to air gap, waste tee or disposer
using the previously determined method. Secure
hose with a screw-type clamp.
Method 1 – Air gap with waste tee or disposer
Method 2 – “High drain loop” with waste tee or
disposer
With this method you will need the drain hose hanger
set aside in Step 1.
Fasten drain hose to underside of countertop with the
provided hanger.
IMPORTANT –
When connecting drain line to
disposer, check to be sure that drain plug has been
removed. DISHWASHER WILL NOT DRAIN IF PLUG
IS LEFT IN PLACE.
Tip: Avoid unnecessary service call charges for a
no drain complaint.
Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose
in the dishwasher cavity from becoming kinked or
crushed by the dishwasher.
Dishwasher Installation
Remove
Drain
Plug
12
CONNECT DRAIN LINE
The molded end of the drain hose will fit 5/8” through 1”
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port.
• Cut drain hose connector on the marked line, if required,
to fit the inlet port.
• If a longer drain hose is required, replace the
provided user bag drain hose with GE Appliances
service part
WD24X10065
, a 12’ long hose which
can be connected directly to the drain loop already
attached to the unit (see Step 7). If service part hose
is not available, an additional hose with coupler, ID of
5/8” or 7/8” and no longer than 66”, may be attached
to the provided user bag drain hose. Secure the
connection with hose clamp (obtain locally) to the
provided user bag drain hose.
NOTES:
• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED
72” ABOVE BOTTOM OF DISHWASHER.
• TOTAL DRAIN HOSE LENGTH MUST NOT
EXCEED 12 FEET FOR PROPER DRAIN
OPERATION.
Figure Z
Cutting Line
1"
5/8"
IMPORTANT:
Do not cut corrugated
portion of hose
STEP 17
STEP 17
Hose
Clamp
Coupler
Hose
Clamp
Figure AA
Figure AB
Disposer Installation
Waste Tee Installation
Waste Tee Installation
Figure AC
18"
Min.
32"
Min.
32"
Min.
18"
Min.
Drain Hose Hanger
Drain Hose Hanger
Disposer Installation