Haier QNE27JYMFS Use and Care Manual - Page 12

Clearances, Installing The Refrigerator - French Doors

Get Haier QNE27JYMFS PDF manuals and user guides View all Haier QNE27JYMFS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

INSTALLATION INSTRUCTIONS INSTALLING THE REFRIGERATOR - FRENCH DOORS • Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures. • Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly. • Do not install the refrigerator in a location exposed to water (rain, etc.) or direct sunlight. • Install it on a floor strong enough to support it fully loaded. CLEARANCES Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections. Sides 1/8" (3 mm) Top 1" (25 mm) Cabinet/Hinge Cover Back 2" (50 mm) WARNING Follow all steps. Failure to follow these instructions, leaving off parts, or overtightening screws, can lead to the door falling off and result in injury and property damage. 1. REMOVING DOORS (Right) A. Remove the hinge cover on top of the right fresh food door by removing the screw using a Phillips screwdriver. B. Using a 5/16" socket ratchet/ driver, remove the bolts securing the top hinge to the cabinet. Lift the hinge support straight up to free the hinge pin from the socket in the top of the door. C. Remove the tape from the right door and tilt the door pin. D. Set the door on a non-scratching surface with the inside up. 2. REMOVING DOORS (Left) A. Remove the hinge cover on top of the left fresh food door by removing the screw using a Phillips screwdriver. B. Unplug the 3 wire connectors and move the wires until you can see the screws holding the hinge. Wire Connectors IMPORTANT NOTES When removing french doors: • Read the instructions all the way through before starting. • Place the screws by their related parts to avoid using them in the wrong places. • Provide a non-scratching work surface for the doors. CAUTION Lifting Hazard. Single person lift can cause injury. Use assistance when handling, moving or lifting the refrigerator doors. NOTE: When moving door, to prevent damage to door and electronics carefully place the door in a proper location. WARNING To eliminate the risk of electric shock or injury during installation, you must first unplug the refrigerator before proceeding. Failure to follow these instructions can result in electrical shock. C. Using a 5/16" socket/ratchet driver, remove the bolts securing the top hinge to the cabinet. Wire Connectors Bolts Tape the doors shut with adhesive tape. 12 ENGLISH 49-60806 Rev. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
12
49-60806
Rev. 1
ENGLISH
1. REMOVING DOORS (Right)
A.
Remove the hinge cover on
top of the right fresh food
door by removing the screw
using a Phillips screwdriver.
B.
Using a 5/16” socket ratchet/
driver, remove the bolts
securing the top hinge to
the cabinet. Lift the hinge
support straight up to free
the hinge pin from the socket in the top of the door.
C.
Remove the tape from the right door and tilt the door
pin.
D.
Set the door on a non-scratching surface with the
inside up.
2. REMOVING DOORS (Left)
A.
Remove the hinge cover on
top of the left fresh food door
by removing the screw using a
Phillips screwdriver.
B.
Unplug the 3 wire connectors
and move the wires until you
can see the screws holding the
hinge.
C.
Using a 5/16” socket/ratchet driver, remove the bolts
securing the top hinge to the cabinet.
IMPORTANT NOTES
When removing french doors:
•
Read the instructions all the way through before starting.
•
Place the screws by their related parts to avoid using them
in the wrong places.
•
Provide a non-scratching work surface for the doors.
Tape the doors shut with adhesive tape.
INSTALLATION INSTRUCTIONS
CAUTION
Lifting Hazard.
Single person lift can cause injury. Use assistance when
handling, moving or lifting the refrigerator doors.
NOTE:
When moving door, to prevent damage to door
and electronics carefully place the door in a proper
location.
WARNING
To eliminate the risk of electric shock or injury during
installation, you must first unplug the refrigerator before
proceeding. Failure to follow these instructions can result
in electrical shock.
Wire Connectors
Bolts
WARNING
Follow all steps. Failure to follow these
instructions, leaving off parts, or overtightening screws,
can lead to the door falling off and result in injury and
property damage.
•
Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
•
Do not install the refrigerator where the temperature
will go above 100°F (37°C) because it will not perform
properly.
•
Do not install the refrigerator in a location exposed to
water (rain, etc.) or direct sunlight.
•
Install it on a floor strong enough to support it fully
loaded.
CLEARANCES
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
Sides
1/8” (3 mm)
Top
1” (25 mm)
Cabinet/Hinge Cover
Back
2” (50 mm)
INSTALLING THE REFRIGERATOR - FRENCH DOORS
Wire Connectors