Harman Kardon AVR 510 Owners Manual - Page 34

Advanced Features

Get Harman Kardon AVR 510 PDF manuals and user guides View all Harman Kardon AVR 510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Advanced Features the AVR 510 is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session. To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED SELECT menu as outlined earlier, and press the ⁄/¤ buttons n as needed, until the on-screen › cursor is next to the SEMI OSD TIME OUT line. Next, press the ‹/› buttons o 31 until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a permanent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button p. If you have no other adjustments to make, press the OSD button v to exit the menu system. Full-OSD Time-Out Adjustment The FULL OSD menu system is used to simplify the setup and adjustment of the AVR 510, using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen (Time-Out). Time-Out is a safety measure to prevent image retention of the menu text in your monitor or projector, which might happen if it were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display. To change the Full-OSD Time-Out, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 9). To start the adjustment, press the OSD button v to bring the MASTER MENU to the screen. Press the ¤ button n six times, until the on-screen ¤ cursor is next to the ADVANCED line. Press the Set button p to enter the ADVANCED SELECT Menu (Figure 9). At the ADVANCED SELECT menu (Figure 9) make certain that the on-screen › cursor is next to the FULL OSD TIME OUT line by pressing the ⁄/¤ buttons n as needed. Next, press the ‹/› buttons o/ 31 until the desired time is displayed in seconds. Note that unlike most of the other options in this menu, this is a permanent setting change, and the Time-Out entry will remain in effect until it is changed, even if the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MENU line and press the Set button p. If you have no other adjustments to make, press the OSD button v to exit the menu system. 34 ADVANCED FEATURES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
34
ADVANCED FEATURES
Advanced Features
the AVR 510 is turned off. Once the unit is
turned off, the semi-OSD displays will remain
activated, even if they were switched off for the
previous listening session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCEDSELECT
menu as outlined
earlier, and press the
⁄
/
¤
buttons
n
as
needed, until the on-screen
›
cursor is next to
the
SEMIOSDTIMEOUT
line. Next,
press the
‹
/
›
buttons
o
until the
desired time in seconds is displayed. Note that
unlike most of the other options in this menu,
this is a permanent setting change, and the
time-out entry will remain in effect until it is
changed, even when the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
buttons
n
until the on-screen
›
cursor is next to the desired setting or the
RETURNTOMENU
line and press the
Set
button
p
. If you have no other adjustments
to make, press the
OSD
button
v
to exit the
menu system.
Full-OSD Time-Out Adjustment
The
FULLOSD
menu system is used to sim-
plify the setup and adjustment of the AVR 510,
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of
inactivity before they disappear from the screen
(Time-Out). Time-Out is a safety measure to
prevent image retention of the menu text in
your monitor or projector, which might happen
if it were left on indefinitely. However, some
viewers may prefer a slightly longer or shorter
period before the Time Out display.
To change the Full-OSD Time-Out, you will need
to make an adjustment in the
ADVANCED
SELECT
menu (Figure 9). To start the
adjustment, press the
OSD
button
v
to bring
the
MASTERMENU
to the screen. Press
the
¤
button
n
six times, until the on-screen
¤
cursor is next to the
ADVANCED
line.
Press the
Set
button
p
to enter the
ADVANCEDSELECT
Menu (Figure 9).
At the
ADVANCEDSELECT
menu
(Figure 9) make certain that the on-screen
›
cursor is next to the
FULLOSDTIME
OUT
line by pressing the
⁄
/
¤
buttons
n
as
needed. Next, press the
‹
/
›
buttons
o
/
until the desired time is displayed in seconds.
Note that unlike most of the other options in
this menu, this is a permanent setting change,
and the Time-Out entry will remain in effect
until it is changed, even if the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
buttons
n
until the on-screen
›
cursor is next to the desired setting or the
RETURNTOMENU
line and press the
Set
button
p
. If you have no other adjustments
to make, press the
OSD
button
v
to exit the
menu system.
31
31