HealthRider C535e Elliptical English Manual - Page 8

Right Pedal 12 to the Right Pedal Arm 103 in

Page 8 highlights

7. Apply a thin film of grease to the shaft of an 7 M10 x 52mm Bolt Set (27) and to the surfaces of the 79 two Leg Bushings (28) in the left Handlebar Leg (79). 79 Next, attach the left Handlebar Leg (79) to the Left Grease 103 Pedal Arm (14) with the M10 x 52mm Bolt Set (27). Do not overtighten the Bolt Set; the left Handlebar Leg 28 28 27 must be able to pivot freely. Attach the right Handlebar Leg (79) to the Right Pedal Grease Arm (103) in the same way. 27 See step 3. Tighten the M10 x 88mm Button Screws (63). See step 6. Tighten the M8 x 45mm Button 14 Bolts (50) in the Handlebar Legs (79). 8. Attach a Pedal Bracket (16) to the Left Pedal Arm (14) with two M8 x 65mm Button Screws (99), two M8 Large 8 Washers (53), and two M8 Nylon Locknuts (46). 103 12 Identify the Left Pedal (13). Attach the Left Pedal to the Left Pedal Arm (14) with two M8 x 50mm Button Screws (89), two M8 Split Washers (100) and two M8 Large Washers (53). Attach the other Pedal Bracket (not shown) and the Right Pedal (12) to the Right Pedal Arm (103) in the same way. 46 53 14 53 13 16 99 100 53 89 9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

8
9.
Make sure that all parts of the elliptical exerciser are properly tightened.
Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the ellip-
tical exerciser.
8
12
16
99
14
13
8.
Attach a Pedal Bracket (16) to the Left Pedal Arm (14)
with two M8 x 65mm Button Screws (99), two M8 Large
Washers (53), and two M8 Nylon Locknuts (46).
Identify the Left Pedal (13). Attach the Left Pedal to the
Left Pedal Arm (14) with two M8 x 50mm Button
Screws (89), two M8 Split Washers (100) and two M8
Large Washers (53).
Attach the other Pedal Bracket (not shown) and the
Right Pedal (12) to the Right Pedal Arm (103) in the
same way.
103
53
53
53
46
89
100
7.
Apply a thin film of grease to the shaft of an
M10 x 52mm Bolt Set (27) and to the surfaces of the
two Leg Bushings (28) in the left Handlebar Leg (79).
Next, attach the left Handlebar Leg (79) to the Left
Pedal Arm (14) with the M10 x 52mm Bolt Set (27).
Do
not overtighten the Bolt Set; the left Handlebar Leg
must be able to pivot freely.
Attach the right Handlebar Leg (79) to the Right Pedal
Arm (103) in the same way.
See step 3. Tighten the M10 x 88mm Button Screws
(63). See step 6. Tighten the M8 x 45mm Button
Bolts (50) in the Handlebar Legs (79).
14
103
27
27
28
28
Grease
Grease
7
79
79