HealthRider R 60 English Manual - Page 7

Remove the Lock Knob 67 from the Lock Pin 72. Make - troubleshooting

Page 7 highlights

3. With the help of a second person, raise the Frame (55). 3 Hold the Latch Housing (68) and the Latch Housing Cover (5) against the sides of the Frame (55) as shown. Loosely screw the two 1/2" Screws (132) into the Latch Housing Cover and the Latch Housing as shown. Do not tighten the Screws yet. Hole Remove the Lock Knob (67) from the Lock Pin (72). Make sure that the Lock Pin Collars (70) and the Spring (69) are on the Lock Pin. The Lock Pin Collars should be on each side of the Spring. Insert the Lock Pin into the Latch Housing (68), and tighten the Lock Knob onto it. Align the Lock Pin (72) with the hole in the Left Foam Grip (62) by sliding the Latch Housing (68) up or down. Make sure that the Lock Pin can be inserted fully into the hole. Hold the Latch Housing in place as you tighten two 3/4" Screws (40) in the Latch Housing and the Frame (55). Tighten the 1/2" Screws (132). Note: It may be necessary to pull on the Lock Knob (67) to access and tighten the Screws. 62 68 40 70 69 69 40 72 40 67 5 132 Small Holes 55 132 4. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the treadmill to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with the TROUBLESHOOTING section on pages 26 and 27. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34

7
68
5
69
69
70
40
55
67
132
3
Small
Holes
3.
With the help of a second person, raise the Frame (55).
Hold the Latch Housing (68) and the Latch Housing Cover
(5) against the sides of the Frame (55) as shown. Loosely
screw the two 1/2” Screws (132) into the Latch Housing
Cover and the Latch Housing as shown.
Do not tighten
the Screws yet.
Remove the Lock Knob (67) from the Lock Pin (72). Make
sure that the Lock Pin Collars (70) and the Spring (69) are
on the Lock Pin. The Lock Pin Collars should be on each
side of the Spring. Insert the Lock Pin into the Latch
Housing (68), and tighten the Lock Knob onto it.
Align the Lock Pin (72) with the hole in the Left Foam Grip
(62) by sliding the Latch Housing (68) up or down. Make
sure that the Lock Pin can be inserted fully into the hole.
Hold the Latch Housing in place as you tighten two 3/4”
Screws (40) in the Latch Housing and the Frame (55).
Tighten the 1/2” Screws (132). Note: It may be necessary
to pull on the Lock Knob (67) to access and tighten the
Screws.
4.
Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet.
For your benefit, we recommend that you familiarize yourself with
the TROUBLESHOOTING section on pages 26 and 27.
Hole
72
62
132
40
40