HP 1320n HP LaserJet 1320nw - User Guide - Page 16

The printer's Internet Protocol IP address. This address, Subnet Mask - config page

Get HP 1320n - LaserJet B/W Laser Printer PDF manuals and user guides
UPC - 829160407364
View all HP 1320n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Field Firmware Version Description The internal networking component and device firmware revision code separated by a hyphen. Host Name IP Address Subnet Mask Note You might be asked to provide the firmware revision code if you call for support. The TCP/IP name assigned by the install software to the device. By default, this is the letters NPI followed by the last six digits of the MAC address. You can also configure the device name through the embedded Web server. The printer's Internet Protocol (IP) address. This address uniquely identifies the device on the network. IP addresses are assigned dynamically through DHCP or AutoIP. You can also set up a static IP address, though this is not recommended. Manually assigning an invalid IP address during install will cause your network components to not see the device. A subnet is an IP address assigned by the install software to make an additional network available as part of a larger network. Subnets are specified by a subnet mask. This mask determines which bits of the printer's IP address identify the network and subnet and which bits identify the device itself. Default Gateway Note It is recommended that the printer and the computers that use the subnet mask all reside on the same subnet. A node on a network that serves as an entrance to another network. A node in this instance can be a computer or some other device. Config by Note The address of the default gateway is assigned by the install software. The protocol used to assign the IP address to the device: ● Automatic (AutoIP): the installation software determines the configuration parameters. ● DHCP: the configuration parameters are supplied by a dynamic host configuration protocol (DHCP) server on the network. On small networks, this could be a router. ● Manual: the configuration parameters are set manually, such as a static IP address. ● Not Specified: mode when initializing. 10 2 Support information for installing to a wireless network ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
10
2
Support information for installing to a wireless network
ENWW
Firmware Version
The internal networking component and device firmware
revision code separated by a hyphen.
Note
You might be asked to provide the firmware
revision code if you call for support.
Host Name
The TCP/IP name assigned by the install software to the
device. By default, this is the letters NPI followed by the last six
digits of the MAC address. You can also configure the device
name through the embedded Web server.
IP Address
The printer’s Internet Protocol (IP) address. This address
uniquely identifies the device on the network.
IP addresses are assigned dynamically through DHCP or
AutoIP. You can also set up a static IP address, though this is
not recommended.
Manually assigning an invalid IP address during install will
cause your network components to not see the device.
Subnet Mask
A subnet is an IP address assigned by the install software to
make an additional network available as part of a larger
network. Subnets are specified by a subnet mask. This mask
determines which bits of the printer’s IP address identify the
network and subnet and which bits identify the device itself.
Note
It is recommended that the printer and the
computers that use the subnet mask all
reside on the same subnet.
Default Gateway
A node on a network that serves as an entrance to another
network. A node in this instance can be a computer or some
other device.
Note
The address of the default gateway is
assigned by the install software.
Config by
The protocol used to assign the IP address to the device:
●
Automatic (AutoIP): the installation software determines the
configuration parameters.
●
DHCP: the configuration parameters are supplied by a
dynamic host configuration protocol (DHCP) server on the
network. On small networks, this could be a router.
●
Manual: the configuration parameters are set manually,
such as a static IP address.
●
Not Specified: mode when initializing.
Field
Description