HP 6125XLG R2306-HP 6125XLG Blade Switch EVB Command Reference - Page 16

evb vdp timer keepalive exponent, Syntax, Default, Views, Predefined user roles, Parameters

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Use undo evb s-channel to remove an S-channel on a port. Syntax evb s-channel channel-id service-vlan svlan-id undo evb s-channel channel-id Default Only an automatically created default S-channel, with both SCID and SVID as 1, exists on a port with EVB enabled. Views Ethernet interface view Predefined user roles network-admin Parameters channel-id: Specifies an S-channel ID (SCID) in the range of 2 to 167. 0 is the reserved SCID, and 1 is the default SCID. svlan-id: Specifies an S-VLAN ID (SVID) in the range of 2 to 4094. 1 is the SVID for the default S-channel. Usage guidelines • An S-channel is automatically created through CDCP, and the command line corresponding to the action is added to the configuration file on the bridge. You can also manually create an S-channel by using this command. If an (SCID, SVID) pair for an S-channel is created both automatically and manually, the automatically created S-channel takes precedence. • After an S-channel is created, an S-channel interface is automatically generated. Removing an S-channel also removes the corresponding S-channel interface. A manually created S-channel interface operates in access mode, and an S-channel interface that is automatically created through CDCP operates in trunk mode. • When you manually create an S-channel, do not use the SCID or SVID being used by any other S-channel. Otherwise, an error is displayed. • Create an S-channel on a port with EVB enabled. Otherwise, an error is displayed. • To manually create or remove S-channel, disable CDCP to automatically perform these operations. Examples # Create an S-channel on Twenty-GigabitEthernet 1/0/1, with the SCID 10 and SVID 5. system-view [Sysname] interface TwentyGigE 1/0/1 [Sysname-TwentyGigE1/0/1] evb s-channel 10 service-vlan 5 Related commands • evb enable • interface s-channel evb vdp timer keepalive exponent Use evb vdp timer keepalive exponent to configure a VDP keepalive exponent. Use undo evb vdp timer keepalive exponent to restore the default. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
13
Use
undo evb s-channel
to remove an S-channel on a port.
Syntax
evb s-channel
channel-id
service-vlan
svlan-id
undo evb s-channel
channel-id
Default
Only an automatically created default S-channel, with both SCID and SVID as 1, exists on a port with EVB
enabled.
Views
Ethernet interface view
Predefined user roles
network-admin
Parameters
channel-id
: Specifies an S-channel ID (SCID) in the range of 2 to 167.
0
is the reserved SCID, and
1
is the
default SCID.
svlan-id
: Specifies an S-VLAN ID (SVID) in the range of 2 to 4094.
1
is the SVID for the default S-channel.
Usage guidelines
•
An S-channel is automatically created through CDCP, and the command line corresponding to the
action is added to the configuration file on the bridge. You can also manually create an S-channel
by using this command. If an (SCID, SVID) pair for an S-channel is created both automatically and
manually, the automatically created S-channel takes precedence.
•
After an S-channel is created, an S-channel interface is automatically generated. Removing an
S-channel also removes the corresponding S-channel interface. A manually created S-channel
interface operates in access mode, and an S-channel interface that is automatically created through
CDCP operates in trunk mode.
•
When you manually create an S-channel, do not use the SCID or SVID being used by any other
S-channel. Otherwise, an error is displayed.
•
Create an S-channel on a port with EVB enabled. Otherwise, an error is displayed.
•
To manually create or remove S-channel, disable CDCP to automatically perform these operations.
Examples
# Create an S-channel on Twenty-GigabitEthernet 1/0/1, with the SCID
10
and SVID
5
.
<Sysname> system-view
[Sysname] interface TwentyGigE 1/0/1
[Sysname-TwentyGigE1/0/1] evb s-channel 10 service-vlan 5
Related commands
•
evb enable
•
interface s-channel
evb vdp timer keepalive exponent
Use
evb vdp timer keepalive exponent
to configure a VDP keepalive exponent.
Use
undo evb vdp timer keepalive exponent
to restore the default.