HP Brio 83xx hp brio 83xx, online reference guide - Page 59

Installing the Drive

Get HP Brio 83xx PDF manuals and user guides View all HP Brio 83xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Installing the Drive 3 Upgrading and Adding Accessories Adding Accessories 1 Remove the computer's cover (refer to "Removing the Cover" on page 39). 2 Install the new hard disk drive in the computer: • For a 3.5-inch hard disk drive - mount the new hard disk drive in the 3.5-inch bay (below the floppy disk drive). Have the connectors of the new hard disk drive pointing towards the back of the computer. • For a 5.25-inch hard disk drive - mount the new hard disk in the 5.25-inch bay. Have the connectors of the new hard disk drive pointing towards the back of the computer. 3 Secure the drive to the computer using the four screws provided with the drive. Two screws must be inserted in each side of the drive. Using screws other than those provided may cause damage to the device. 4 Connect the power and data cables to the rear of the drive. Both connectors are shaped to fit one way only. Use the second connector on the hard disk drive data cable. Refer to "System Board Connectors" on page 57 for an illustration of the cables and connectors. Data Cable Storage Device Power Cable 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
59
3
Upgrading and Adding Accessories
Adding Accessories
Installing the Drive
1
Remove the computer’s cover (refer to
“Removing the Cover” on page 39
).
2
Install the new hard disk drive in the computer:
•
For a 3.5-inch hard disk drive – mount the new hard disk drive in the 3.5-inch bay (below the floppy disk drive). Have
the connectors of the new hard disk drive pointing towards the back of the computer.
•
For a 5.25-inch hard disk drive – mount the new hard disk in the 5.25-inch bay. Have the connectors of the new hard
disk drive pointing towards the back of the computer.
3
Secure the drive to the computer using the four screws provided with the drive. Two screws must be inserted in each
side of the drive. Using screws other than those provided may cause damage to the device.
4
Connect the power and data cables to the rear of the drive. Both connectors are shaped to fit one way only. Use the
second connector on the hard disk drive data cable. Refer to
“System Board Connectors” on page 57
for an illustration
of the cables and connectors.
Power Cable
Data Cable
Storage Device