HP Cluster Platform Hardware Kits v2010 HP ProCurve 2610 Series Rail Kit Insta
HP Cluster Platform Hardware Kits v2010 Manual
View all HP Cluster Platform Hardware Kits v2010 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Cluster Platform Hardware Kits v2010 manual content summary:
- HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 1
HP ProCurve 2610 Series Rail Kit Installation Guide HP Part Number: 508783-doc Published: November 2008 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 2
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 3
...9 1.8 Installation Preparations...10 2 Installing the HP ProCurve 2610 Series Rack Mount Brackets 11 3 Cabling and Power...15 4 Removing an HP ProCurve 2610 Series Switch for Servicing 17 Table of Contents 3 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 4
List of Figures 1-1 HP ProCurve 2610 Series Rail Kit Hardware 8 1-2 Support Bracket...9 1-3 Bracket Orientation...10 2-1 Attach the Support Brackets...11 2-2 Attach the Mounting Brackets...12 2-3 HP ProCurve 2610 Series Switch Attached to Rear of the Rack 12 2-4 HP ProCurve 2610 Series Switch - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 5
List of Tables 1-1 Fasteners...8 5 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 6
6 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 7
for Installation 1.1 Audience This guide is intended for HP service representatives and other persons trained to for installation and gather required resources 4. Identify the installation location 5. Attach the support brackets to the rack 6. Attach the mounting brackets to the switch 7. Attach - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 8
Figure 1-2. Figure 1-1 HP ProCurve 2610 Series Rail Kit Hardware 2 3 2 4 1 5 The following list corresponds to the callouts shown in Figure 1-1: 1. Left mounting bracket 2. Two support brackets 3. Right mounting bracket 4. Flat-head M4 screws 5. Pan-head M6 screws 8 Preparing for Installation - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 9
Figure 1-2 Support Bracket • Contact your HP representative if any parts of the kit are missing or damaged. The HP ProCurve 2610 Series rail kit is used for - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 10
2. Right mounting bracket. 3. The ProCurve 2610 series switch. 4. Support bracket mounting position. See Figure 2-1 for more information on where and how to mount the support bracket. 5. M6 screws. 6. M4 screws. 1.8 Installation Preparations - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 11
rails (see callout 4 in Figure 2-1). 3. Locate the same U location on the right and left secondary mounting rails of the rack and attach one support bracket (callout 3 in Figure 2-1) using two M6 screws (callout 2 in Figure 2-1) on each side. Figure 2-1 shows the outer rail of the rack (callout - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 12
RPS Act FDx Test Spd Reset Clear Off=10 Mbps. 6. Make sure that the support bracket's mounting holes line up with the mounting holes in the right and left support brackets. Fasten both of the mounting brackets to the support brackets with two M6 screws, one for each side. See Figure 2-4. 12 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 13
Figure 2-4 HP ProCurve 2610 Series Switch Attached to Front of the Rack 7. Tighten all of the screws to the recommended torque (see Table 1-1 for the recommendations). Note: HP recommends that you use an adjustable torque drive set to the torque specifications provided in Table 1-1. The assembly and - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 14
14 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 15
3 Cabling and Power Follow the installation instructions for your cluster configuration bundle that was shipped with this kit. See Section 1.2 for information on where you can obtain product documentation resources. It is - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 16
16 - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 17
4 Removing an HP ProCurve 2610 Series Switch for Servicing Bring the cluster to an appropriate state and put information on how to do this, see the ProCurve Switch 2610 Series Installation and Getting Started Guide. To remove an HP ProCurve 2610 Series switch from a rack, reverse the steps shown in - HP Cluster Platform Hardware Kits v2010 | HP ProCurve 2610 Series Rail Kit Insta - Page 18
*508783-doc* Printed in the US
HP ProCurve 2610 Series
Rail Kit Installation Guide
HP Part Number: 508783-doc
Published: November 2008