Home » HP Manuals » Servers » HP Cluster Platform Interconnects v2010 » Manual Viewer

HP Cluster Platform Interconnects v2010 Myrinet System Interconnect Guide - Page 15

Dual-port 2XP PCI, Table 2-1: XP PCI Host Interface Card Specifications

Get HP Cluster Platform Interconnects v2010 PDF manuals and user guides

View all HP Cluster Platform Interconnects v2010 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Table 2-1 shows the single-port XP PCI card's technical specifications. Table 2-1: XP PCI Host Interface Card Specifications Feature Specifications XP PCI card 64-bit PCI-X PCI low-profile PCI short card Bus speed 75-133 MHz PCI-X slots 66 MHz (3.3V) PCI slots Memory 2 MB Memory bandwidth 1,800 MB/s Processor 225 MHz RISC Notes LANai XP Data rate Fiber port physical Fiber port data rate EEPROM 490 MB/s LC-type optical connector, 50/125 multimode fiber pair 2.0+2.0 Gb/s data rate, 2.5+2.5 GBaud signaling 512 KB User-level bidirectional data rate. Class I Laser Product (no hazard) Serial number, MAC address, product code, and other information Table 2-2describes the XP PCI card's physical and environmental characteristics. Table 2-2: XP PCI Card Physical Characteristics Characteristic Specifications Dimensions (excluding faceplate) 6.4 cm high, 6.4 cm long, 2.2 cm total thickness Mass 0.082 kg Power requirement 3.3V from the PCI bus, 1.8A (6W) maximum Environmental, operating 0C to 50C up to 10,000 foot altitude Relative humidity 15% to 80% @ 50C Environmental, nonoperating -40C to 70C Relative humidity 90% @ 65C 2.3 Dual-port 2XP PCI The dual-port 2XP PCI NIC (Figure 2-3) is the Myricom Rev. E card. It supports two X-port interfaces and one PCI-X interface. PCI cards 2-3

Section	Page
Table of Contents	1
Audience	5
Organization	5
Additional documentation	5
Providing feedback	5
Symbols in text	6
Myrinet interconnect overview	7
1.1 Interconnect characteristics	7
Figure 1-1: Fat Tree Topology	7
1.2 Backplane and chassis types	8
Figure 1-2: Myrinet System Interconnect Backplane	8
Figure 1-3: Federated Configuration Switches	8
Figure 1-4: Nonfederated Configuration Switch	9
Figure 1-5: 128-Port Myrinet System Interconnect	10
1.3 Wiring rules	10
Figure 1-6: Fully Populated 128-Port Myrinet System Interconnect	11
PCI cards	13
2.1 General characteristics	13
Figure 2-1: PCI Identification Label	13
2.2 Single-port XP PCI card	14
Figure 2-2: Single-port XP PCI Rev. D card	14
2.3 Dual-port 2XP PCI	15
Figure 2-3: Myricom 2XP PCI Rev. E card	16
2.4 Single-port 2XP PCI	17
Figure 2-4: Myricom 2XP PCI Rev. F card	18
Switch, spine and monitoring line cards	19
3.1 Switch card	19
Figure 3-1: Myrinet system Interconnect 8-port switch card	19
Figure 3-2: External features of the Myrinet system interconnect	19
Figure 3-3: Myrinet system interconnect 8-Port GigE switch card	20
Figure 3-4: Block Diagram of the gigabit ethernet switch card	21
3.2 Spine card	21
Figure 3-5: Spine Card Block Diagram	22
3.3 Monitoring line card	22
Figure 3-6: Monitoring Line Card	23
Figure 3-7: External Features of the Monitoring Line Card	23
LED indications and diagnostics	25
4.1 Line card and PCI LEDs	25
4.2 Using LEDs for diagnostics	25
4.3 Using the monitoring line card for diagnostics	26
Replacing components	29
5.1 Installing a monitoring line card	29
5.2 Removing and installing an 8-port line card	30
Figure 5-1: Unlocking Switch Card Handles	30
Figure 5-2: Ejecting a Switch Card	31
Figure 5-3: Sliding a Switch Card	31
Figure 5-4: Backplane Power Connector	31
5.3 Replacing a fan tray	32
Figure 5-5: Removing a Fan Tray	32
5.4 Replacing an interconnect chassis	33
Powering up procedure	39