HP Designjet L65500 HP Designjet L65500 Printer - User's guide: English - Page 22

Handle the substrate, HP offers recyclable substrates such as HP HDPE Reinforced Banner - latex

Get HP Designjet L65500 PDF manuals and user guides View all HP Designjet L65500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Handle the substrate Before loading a roll: ● Check that neither the roll nor its core are bent or deformed, which may cause the substrate to jam in the printer. ● If the roll has been stored in a place not offering the recommended environmental conditions, allow some time for it to adapt to the temperature and humidity of the printer's environment. ● Check which is the correct side for printing, by reading the label inside the core or the note inserted into the package (or see Tips for specific substrates on page 19). ● Check that the substrate is correctly attached to the input core. Otherwise, you will see poor print quality due to substrate advance errors. ● You may find it easier to load a roll if you first move the carriage beam to its highest position. While loading a roll, make sure the leading edge is parallel and straight across the output core, and attached evenly (start taping the substrate to the core at the center, then move towards the edges). After you have loaded a roll: ● Make sure that the edge holders are set on both sides of the roll. An incorrectly loaded roll may cause waves or cockles in the substrate, leading to ink smearing and printhead crashes. ● Check the correct carriage beam position for printing: high for thick substrates, normal for others. See Set the carriage beam position on page 19. ● Check that you are using the correct substrate preset in the HP Internal Print Server and the correct ICC profile and other settings in the RIP. ● HP substrates are optimized to provide the best out-of-the-box printing experience with your printer. However, you may want to modify the ink limits or the number of passes; in which case, temperature, vacuum or tensions may need to be adjusted. You can create a new substrate preset from the default preset you are using and make your changes. ● Use the HP Internal Print Server to check that any required calibrations have been done: color calibration, substrate-advance compensation, printhead alignment. See the Maintenance and troubleshooting guide. ● For the best print quality, the substrate should stay flat and unwrinkled in the printing zone, the substrate advance should be constant and the substrate should move straight. ● Do not cut off pieces of substrate while the substrate is loaded into the printer. This may cause the remaining substrate to jam. After printing, try to allow 24 hours before stacking, folding or rolling printed substrates. You can find further information on the Web: ● The specifications, finishing, processing and warranty information for each individual HP substrate are available from http://www.hp.com/go/designjet/supplies/latex/. ● HP Image Permanence information is available from http://www.hp.com/go/supplies/ printpermanence/. ● HP offers recyclable substrates such as HP HDPE Reinforced Banner, HP Wrinkle-free Flag with liner, HP Heavy Textile Banner, HP Photo-realistic Poster Paper and HP DuPont™ Tyvek® Banner. Recycling opportunities for these products may not exist in all areas. You should consult local recycling resources about recycling these products. For recycling in the USA, please go to the HP recycling services site, http://www.hp.com/go/recycleLFmedia/. 18 Chapter 3 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Before loading a roll:
●
Check that neither the roll nor its core are bent or deformed, which may cause the substrate to jam
in the printer.
●
If the roll has been stored in a place not offering the recommended environmental conditions, allow
some time for it to adapt to the temperature and humidity of the printer's environment.
●
Check which is the correct side for printing, by reading the label inside the core or the note inserted
into the package (or see
Tips for specific substrates
on page
19
).
●
Check that the substrate is correctly attached to the input core. Otherwise, you will see poor print
quality due to substrate advance errors.
●
You may find it easier to load a roll if you first move the carriage beam to its highest position.
While loading a roll, make sure the leading edge is parallel and straight across the output core, and
attached evenly (start taping the substrate to the core at the center, then move towards the edges).
After you have loaded a roll:
●
Make sure that the edge holders are set on both sides of the roll. An incorrectly loaded roll may
cause waves or cockles in the substrate, leading to ink smearing and printhead crashes.
●
Check the correct carriage beam position for printing: high for thick substrates, normal for others.
See
Set the carriage beam position
on page
19
.
●
Check that you are using the correct substrate preset in the HP Internal Print Server and the correct
ICC profile and other settings in the RIP.
●
HP substrates are optimized to provide the best out-of-the-box printing experience with your printer.
However, you may want to modify the ink limits or the number of passes; in which case,
temperature, vacuum or tensions may need to be adjusted. You can create a new substrate preset
from the default preset you are using and make your changes.
●
Use the HP Internal Print Server to check that any required calibrations have been done: color
calibration, substrate-advance compensation, printhead alignment. See the
Maintenance and
troubleshooting guide
.
●
For the best print quality, the substrate should stay flat and unwrinkled in the printing zone, the
substrate advance should be constant and the substrate should move straight.
●
Do not cut off pieces of substrate while the substrate is loaded into the printer. This may cause the
remaining substrate to jam.
After printing, try to allow 24 hours before stacking, folding or rolling printed substrates.
You can find further information on the Web:
●
The specifications, finishing, processing and warranty information for each individual HP substrate
are available from
go/designjet/supplies/latex/
.
●
HP Image Permanence information is available from
go/supplies/
printpermanence/
.
●
HP offers recyclable substrates such as HP HDPE Reinforced Banner, HP Wrinkle-free Flag with
liner, HP Heavy Textile Banner, HP Photo-realistic Poster Paper and HP DuPont™ Tyvek® Banner.
Recycling opportunities for these products may not exist in all areas. You should consult local
recycling resources about recycling these products. For recycling in the USA, please go to the HP
recycling services site,
go/recycleLFmedia/
.
18
Chapter 3
Handle the substrate
ENWW
Handle the substrate