HP Designjet L65500 HP Designjet L65500 Printer - User's guide: English - Page 30

Unload a roll

Get HP Designjet L65500 PDF manuals and user guides View all HP Designjet L65500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

22. Go to the HP Internal Print Server and select the Substrate menu, then Loaded substrate. Choose from the list of substrate types the type that you have loaded. Handle the substrate The contents of the Loaded Substrate window are determined automatically when the substrate is loaded and checked. However, if the printer is unable to detect the edges of the substrate (for instance, in the case of a transparent substrate), you will have to measure the distance of the left edge from the printer's side plate, and complete the Left Edge and Width fields yourself. For more information on when you might want to change the carriage beam position, see Substrate tips on page 17. An alert regarding substrate advance tracking may appear at this point. For more information on when you might want to turn off automatic tracking, see Fine-tune the settings in your new preset on page 30 and the Maintenance and troubleshooting guide. The printer is now ready to print. Unload a roll 1. Lift the substrate pressure at the rear of the printer. 2. Go to the printer's front panel and select the Substrate menu . 3. Select Carriage beam position > Move to highest position. The printer raises the carriage. This process takes about two minutes to complete. TIP: This step is optional. It may be feasible to unload some substrates without raising the carriage beam. 4. When the carriage has been raised, cut the substrate 5. In the front panel's Substrate menu, select Turn output spindle to wind the substrate onto the output roll. Press the Cancel key to stop winding. 6. Open the front latches and remove the output roll from the printer. 7. Remove the spindle from the roll. 8. In the front panel's Substrate menu, select Turn input spindle to rewind the substrate onto the input roll. Press the Cancel key to stop rewinding. 9. Open the rear latches and remove the input roll from the printer. 10. Remove the spindle from the roll. 11. In the front panel's Substrate menu, select Exit substrate mgt mode > Yes, then reply No to the question "Check loaded substrate before exit substrate management mode?". The printer is now ready for new input and output rolls to be loaded. 26 Chapter 3 Handle the substrate ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
22.
Go to the HP Internal Print Server and select the
Substrate
menu, then
Loaded substrate
. Choose
from the list of substrate types the type that you have loaded.
The contents of the Loaded Substrate window are determined automatically when the substrate is
loaded and checked. However, if the printer is unable to detect the edges of the substrate (for
instance, in the case of a transparent substrate), you will have to measure the distance of the left
edge from the printer's side plate, and complete the Left Edge and Width fields yourself.
For more information on when you might want to change the carriage beam position, see
Substrate
tips
on page
17
.
An alert regarding substrate advance tracking may appear at this point. For more information on
when you might want to turn off automatic tracking, see
Fine-tune the settings in your new
preset
on page
30
and the
Maintenance and troubleshooting guide
.
The printer is now ready to print.
Unload a roll
1.
Lift the substrate pressure at the rear of the printer.
2.
Go to the printer's front panel and select the Substrate menu
.
3.
Select
Carriage beam position
>
Move to highest position
. The printer raises the carriage. This
process takes about two minutes to complete.
TIP:
This step is optional. It may be feasible to unload some substrates without raising the
carriage beam.
4.
When the carriage has been raised, cut the substrate
5.
In the front panel's Substrate menu, select
Turn output spindle
to wind the substrate onto the
output roll. Press the
Cancel
key to stop winding.
6.
Open the front latches and remove the output roll from the printer.
7.
Remove the spindle from the roll.
8.
In the front panel's Substrate menu, select
Turn input spindle
to rewind the substrate onto the
input roll. Press the
Cancel
key to stop rewinding.
9.
Open the rear latches and remove the input roll from the printer.
10.
Remove the spindle from the roll.
11.
In the front panel's Substrate menu, select
Exit substrate mgt mode
>
Yes
, then reply
No
to the
question “Check loaded substrate before exit substrate management mode?”.
The printer is now ready for new input and output rolls to be loaded.
26
Chapter 3
Handle the substrate
ENWW
Handle the substrate