HP ENVY 15-as000 Maintenance and Service Guide - Page 39

Memory module, Remove the memory module

Get HP ENVY 15-as000 PDF manuals and user guides View all HP ENVY 15-as000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

4. If it is necessary to replace the hard drive rubber bracket, release the left and right sides (2) of the rubber bracket from the hard drive, and then remove the rubber bracket (3). Reverse this procedure to reassemble and install the hard drive. Memory module Description 8-GB (2133, 1.2-V, DDR4) 4-GB (2133, 1.2-V, DDR4) 2-GB (2133, 1.2-V, DDR4) Spare part number 820448-858 820447-858 851227-857 Before removing a memory module, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 26). 5. Disconnect the battery cable from the system board (see Battery on page 29). Remove the memory module: 1. Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The memory module tilts up.) Component replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
4.
If it is necessary to replace the hard drive rubber bracket, release the left and right sides
(2)
of the
rubber bracket from the hard drive, and then remove the rubber bracket
(3)
.
Reverse this procedure to reassemble and install the hard drive.
Memory module
Description
Spare part number
8-GB (2133, 1.2-V, DDR4)
820448-858
4-GB (2133, 1.2-V, DDR4)
820447-858
2-GB (2133, 1.2-V, DDR4)
851227-857
Before removing a memory module, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
26
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
29
).
Remove the memory module:
1.
Spread the retaining tabs
(1)
on each side of the memory module slot to release the memory module.
(The memory module tilts up.)
Component replacement procedures
31