HP Kayak XU 04xx HP Kayak XU Series 04xx, HP MaxiLife Hardware Monitoring - Page 27

Cause / Symptom, Short message US, Message, Explanation or Suggestions for Corrective Action

Get HP Kayak XU 04xx PDF manuals and user guides View all HP Kayak XU 04xx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

HP MaxiLife® Hardware Monitoring Error Message Summary Code # Cause / Symptom Short message (US) 0731h Defective DIMM (module 1, bank 3) System Memory Error 0732h Defective DIMM (module 2, bank 3) System Memory Error 0800h Found lower cache size than configured System Cache Error 0801h Cache self-test failure System Cache Error 0900h Lan (Chanteclerc) self-test failure Integrated LAN Error 0901h Lan (Chanteclerc) not detected (but enabled in Setup) Integrated LAN Error 0A00h Plug and Play video auto-setting failure (DDC hang) DDC Video Error The following table summarizes the most significant of the problems that can be reported. Message Operating system not found Missing operating system Resource Allocation Conflict -PCI device 0079 on system board Video Plug and Play interrupted or failed. Re-enable in Setup and try again System CMOS checksum bad - run Setup No message, system "hangs" Other 4 - 4 - 2 - 4 (Beep code) Explanation or Suggestions for Corrective Action Check whether the disk, HDD, FDD or CD-ROM disk drive is connected. If it is connected, check that it is detected by POST. Check that your boot device is enabled on the Setup Security menu. If the problem persists, check that the boot device contains the operating system. If you have configured HDD user parameters, check that they are correct. Otherwise, use HDD type "Auto" parameters. Clear CMOS. You may have powered your computer Off/On too quickly and the computer turned off Video plug and play as a protection. CMOS contents have changed between 2 power-on sessions. Run Setup for configuration. Check that the main memory modules are correctly set in their sockets. An error message may be displayed and the computer may "hang" for 20 seconds and then beep. The POST is probably checking for a mass storage device which it cannot find and the computer is in Time-out Mode. After Time-out, run Setup to check the configuration. Switch 10 is not correctly set or flash is corrupted. The BIOS update crisis recovery procedure is to be used. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
27
HP MaxiLife® Hardware Monitoring
Error Message Summary
The following table summarizes the most significant of the problems that
can be reported.
0731h
Defective DIMM (module 1, bank 3)
System Memory Error
0732h
Defective DIMM (module 2, bank 3)
System Memory Error
0800h
Found lower cache size than configured
System Cache Error
0801h
Cache self-test failure
System Cache Error
0900h
Lan (Chanteclerc) self-test failure
Integrated LAN Error
0901h
Lan (Chanteclerc) not detected (but enabled in
Setup
)
Integrated LAN Error
0A00h
Plug and Play video auto-setting failure (DDC hang)
DDC Video Error
Code #
Cause / Symptom
Short message (US)
Message
Explanation or Suggestions for Corrective Action
Operating system not found
Check whether the disk, HDD, FDD or CD-ROM disk drive is
connected.
If it is connected, check that it is detected by POST
.
Check that your boot device is enabled on the
Setup
Security
menu.
If the problem persists, check that the boot device contains the
operating system.
Missing operating system
If you have configured HDD user parameters, check that they are
correct. Otherwise, use HDD type “Auto” parameters.
Resource Allocation Conflict -PCI device
0079 on system board
Clear CMOS.
Video Plug and Play interrupted or
failed. Re-enable in Setup and try again
You may have powered your computer Off/On too quickly and the
computer turned off Video plug and play as a protection.
System CMOS checksum bad - run
Setup
CMOS contents have changed between 2 power-on sessions. Run
Setup
for configuration.
No message, system “hangs”
Check that the main memory modules are correctly set in their
sockets.
Other
An error message may be displayed and the computer may “hang”
for 20 seconds and then beep. The POST is probably checking for a
mass storage device which it cannot find and the computer is in
Time-out Mode. After Time-out, run
Setup
to check the
configuration.
4 - 4 - 2 - 4 (Beep code)
Switch 10 is not correctly set or flash is corrupted. The BIOS
update crisis recovery procedure is to be used.