HP LH6000r HP Netserver LPr Installation Guide - Page 113

The CD-ROM Drive Does Not Work, The Hard Disk Drive Does Not Work

Get HP LH6000r - NetServer - 0 MB RAM PDF manuals and user guides View all HP LH6000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Chapter 13 Troubleshooting The CD-ROM Drive Does Not Work • Check that a CD-ROM is inserted in the drive. • Check that the power and data cables are correctly connected to the device. • If you intend to boot from the CD-ROM, make sure that Start from CD-ROM is enabled in the Hardware Security submenu located under the Security menu in the Setup utility. • For further information, see your CD-ROM documentation. The Hard Disk Drive Does Not Work If error messages displayed on the monitor indicate a hard disk failure, perform these checks: 1. Check that all SCSI devices have unique SCSI IDs. 3. If you intend to boot from the hard disk drive, make sure that Start from Hard Disk is enabled in the Hardware Security submenu located under the Security menu in the Setup utility. Also verify that the SCSI ID of the hard disk drive is correct for booting. 4. Refer to the HP NetServer Hard Disk Drive Troubleshooting Guide on the HP Web Site at http://www.hp.com/netserver/servsup/trouble/ . 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 13
Troubleshooting
105
The CD-ROM Drive Does Not Work
•
Check that a CD-ROM is inserted in the drive.
•
Check that the power and data cables are correctly connected to
the device.
•
If you intend to boot from the CD-ROM, make sure that
Start from
CD-ROM
is enabled in the Hardware Security submenu located under the
Security menu in the Setup utility.
•
For further information, see your CD-ROM documentation.
The Hard Disk Drive Does Not Work
If error messages displayed on the monitor indicate a hard disk failure, perform
these checks:
1.
Check that all SCSI devices have unique SCSI IDs.
3.
If you intend to boot from the hard disk drive, make sure that
Start from
Hard Disk
is enabled in the Hardware Security submenu located under
the Security menu in the Setup utility. Also verify that the SCSI ID of the
hard disk drive is correct for booting.
4.
Refer to the
HP NetServer Hard Disk Drive Troubleshooting Guide
on the
HP Web Site at
.