Home » HP Manuals » Desktops » HP Model 745 » Manual Viewer

HP Model 745 Model 745 Industrial Controller Owner's Guide - Page 157

Interpreting the LEDs, green LED is labeled POWER.

Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

Dealing With Problems Interpreting the LEDs Interpreting the LEDs The Model 745 provides two LEDs, located to the left and right of the reset switch, as shown in Figure 9-1. The red LED is labeled SYSFAIL and the green LED is labeled POWER. Reset Switch Figure 9-1 Red LED Green LED Model 745 LED Location 9-3

Section	Page
Model 745 Industrial Controller Owner's Guide	1
Contents	3
Figures	10
Tables	12
Preface	13
Audience	14
Release Document(s)	14
Related Manuals	14
Revision History	15
Documentation Conventions	16
Questions, Suggestions, or Problems	17
1 Product Description	19
The Model 745 Industrial Controller	21
Features	23
Typical External Devices	24
Physical Dimensions and Power Requirements	25
Board Computer Configurations	26
Cables	27
Environmental Requirements	28
Operating System Overview	29
Manuals for System Information	30
HP-UX	30
HP VUE	30
HP CDE	30
Online Sources of Information	31
Audio	32
2 Connecting Cables	33
Introduction	35
Connecting a Monitor or Text-Only Terminal	36
Configuration Requirements	36
Connecting the Monitor	36
Monitor Power Cord	37
Connecting a Terminal	39
Audio Connection	40
Video Connection	43
Keyboard and Mouse Connections	44
SCSI Connections	45
Network Connection	48
Printer Connections	50
Preparing for HP-UX Installation	50
Configuring HP-UX for a Printer	50
Printer Interface	50
Printer Cables	51
Installation Procedure	51
Testing the Printer Installation	53
HP Parallel	53
RS-232 Port A	55
3 Power-On/Power-Off	57
Powering On the System	59
Powering Off the System	63
Using SAM to Stop the HP-UX System	64
Using the Command Line	64
4 Processor Options Installation	65
Tools Required and Preliminary Procedures	67
Tools Required for Installation	67
Preliminary Procedures	67
Safety Precautions	68
Removing the Processor Board	69
Memory	70
Preliminary Requirements	70
RAM Card Installation	70
RAM Card Removal	71
PMC Bridge Adapter and Expansion Adapter	72
Preliminary Requirements	72
PMC Bridge Adapter and Expansion Adapter Installation	72
5 EISA Card Installation	85
EISA Accessory Card Configuration Files	87
Hardware Installation	88
Tools Required	88
Procedure	88
6 PCI Card Installation	93
Hardware Installation	95
Tools Required	95
Procedure	95
7 Installing and Configuring Mass Storage Devices	101
Hardware Installation for Drives	103
Tools for Installation	103
Module Orientations	104
Finding the Status of Existing SCSI Bus Addresses	105
Current SCSI Addresses and Devices	105
Installing Mass Storage Devices	106
Accessing the Mass Storage Carriers	106
Removing a Device from the Mass Storage Carriers	106
Installing a Device in a Mass Storage Carrier	108
Configuring for a Hard Disk Drive	115
Software Installation of the Hard Disk Drive Upgrade	115
8 Using Mass Storage Devices	119
Using your CD-ROM Drive	120
CD-ROM Drive and CD-ROM Media Descriptions	121
CD-ROM Drive	121
CD-ROM Media	122
Operating the CD-ROM Drive	124
Loading and Unloading a CD-ROM in the Disc Tray	124
Verifying the CD-ROM Drive Operation	127
Mounting and Unmounting a CD-ROM Disc	129
Mounting a CD-ROM Disc Using SAM	129
Unmounting a CD-ROM Disc Using SAM	131
Reading the Busy Light	132
DDS Tape Drive and Data Cassette Descriptions	133
DDS Drive	133
Data Cassettes	137
Setting the Write-Protect Tab on a Data Cassette	138
Operating the DDS Tape Drive	140
Loading and Unloading a Data Cassette	140
Verifying the DDS Tape Drive Operation	141
Using Device Files	141
Archiving Data	142
Writing to a Data Cassette	142
Restoring Files from a Data Cassette to Your System	143
Listing the Files on a Data Cassette	143
Further Command Information	143
Ordering Information	145
Using the Floppy Diskette	146
Setting the Write-Protect Tab on a Diskette	146
Inserting and Removing a Diskette	147
Operating the Floppy Drive	148
Verifying the Floppy Drive Configuration	148
Using Device Files	148
Formatting a New Diskette	149
Transferring Data To and From a Floppy Diskette	149
Saving Files to a Floppy Diskette	150
Restoring Files from a Floppy Diskette to Your System	150
Listing the Files on a Floppy Diskette	151
Configuring the Floppy Driver	152
Ordering Information	153
9 Dealing With Problems	155
Interpreting the LEDs	157
Managing a Boot Failure	159
Boot Program Initializes Hardware	159
Recovering from a System Panic	160
Procedures for Recovering from a System Panic	162
Dealing with Network Failures	166
Configuring the HP-UX Kernel	167
A Safety and Regulatory Statements	169
Declaration of Conformity	171
Emissions Regulations and Statements	172
Federal Communications Commission (FCC)	172
VCCI Class A ITE	173
Taiwan BCIQ Class A	173
Emissions Regulations Compliance	174
Acoustics	175
Regulation On Noise Declaration For Machines -3. GSGV	175
Electrostatic Discharge (ESD) Precautions	176
Safety Statement	177
Laser Safety Statement	178
Warnings and Cautions	179
B The Boot Console Interface	181
Boot Console User Interface Features	182
Main Menu	183
Configuration Menu	184
Information Menu	185
Service Menu	185
Accessing the Boot Console Interface	186
Booting Your Workstation	188
Searching for Bootable Media	190
Restoring the Factory Default Configuration	191
Displaying and Setting Paths	192
Displaying and Setting the Monitor Type	195
The Monitor Command	195
Displaying the Current Monitor Configuration	196
Setting the Monitor Type	197
Setting the Monitor Type at Power On	199
Using the Emergency Interactive Console Search	200
Displaying the Current Memory Configuration	202
Memory Information Example	202
Displaying the Status of the System I/O	204
Setting the Auto Boot and Auto Search and Auto Start Flags	205
Displaying and Setting the Security Mode	207
Displaying and Setting the Fastboot Mode	208
Displaying the LAN Station Address	209
Displaying System Information	210
Displaying PIM Information	211
Glossary	213