HP NetServer LP 1000r HP Netserver Ultra3 SCSI HBA Guide - Page 19

HP Ultra3 SCSI Host Adapter Driver Software

Get HP NetServer LP 1000r PDF manuals and user guides View all HP NetServer LP 1000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Figure 1-11. Terminating the Last External SCSI Device 4. Terminate only the device at the end of the chain. (Use of an external multi-mode SCSI terminator is required.) 5. Connect power cables to all external devices and to the HP Netserver. HP Ultra3 SCSI Host Adapter Driver Software NOTE To use the HP Ultra3 SCSI host bus adapter, driver software must be installed for your operating system. Preloaded Ultra3 Drivers If the HP Ultra3 SCSI host bus adapter was included as part of a HP Netserver you purchased, then the appropriate HP driver has already been pre-installed by HP and you do not need to install it. Embedded Ultra3 Drivers Some operating systems have embedded driver support for the HP Ultra3 SCSI host bus adapter. To determine if the host adapter is supported by the operating system you are using, read the operating system manual or contact the operating system vendor for information. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
13
Figure 1-11. Terminating the Last External SCSI Device
4. Terminate only the device at the end of the chain. (Use of an external
multi-mode SCSI terminator is required.)
5. Connect power cables to all external devices and to the HP Netserver.
HP Ultra3 SCSI Host Adapter Driver Software
NOTE
To use the HP Ultra3 SCSI host bus adapter, driver software must be
installed for your operating system.
Preloaded Ultra3 Drivers
If the HP Ultra3 SCSI host bus adapter was included as part of a HP Netserver
you purchased, then the appropriate HP driver has already been pre-installed by
HP and you do not need to install it.
Embedded Ultra3 Drivers
Some operating systems have embedded driver support for the HP Ultra3 SCSI
host bus adapter. To determine if the host adapter is supported by the operating
system you are using, read the operating system manual or contact the operating
system vendor for information.