HP Pavilion dv3-4100 HP Pavilion dv3 Entertainment PC - Maintenance and Servic - Page 58

If it is necessary to replace the hard drive connector cable, disconnect the cable

Get HP Pavilion dv3-4100 - Entertainment Notebook PC PDF manuals and user guides View all HP Pavilion dv3-4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

3. Disconnect the hard drive cable from the system board. 4. Use the Mylar tab (1) to lift the rear edge of the hard drive until it rests at an angle. 5. Remove the hard drive (2) by sliding it up and back at an angle. 6. If it is necessary to replace the hard drive bracket, remove the four Phillips PM3.0×3.0 screws (1) that secure the bracket to the hard drive. 7. If it is necessary to replace the hard drive connector cable, disconnect the cable (2) from the hard drive. The hard drive bracket and hard drive connector cable are included in the Hard Drive Hardware Kit, spare part number 603916-001. 48 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
3.
Disconnect the hard drive cable from the system board.
4.
Use the Mylar tab
(1)
to lift the rear edge of the hard drive until it rests at an angle.
5.
Remove the hard drive
(2)
by sliding it up and back at an angle.
6.
If it is necessary to replace the hard drive bracket, remove the four Phillips PM3.0×3.0 screws
(1)
that secure the bracket to the hard drive.
7.
If it is necessary to replace the hard drive connector cable, disconnect the cable
(2)
from the
hard drive. The hard drive bracket and hard drive connector cable are included in the Hard Drive
Hardware Kit, spare part number 603916-001.
48
Chapter 4
Removal and replacement procedures