HP Pavilion t300 HP Pavilion Desktop PC - (English) Users Guide PAV SEA/ANZ/IN - Page 113

after closing the pc, removing the side panel

Get HP Pavilion t300 - Desktop PC PDF manuals and user guides View all HP Pavilion t300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

after closing the pc To avoid injury and equipment damage, always follow this procedure in this order after closing the PC: 1 Reconnect the power cord and all other attached cables (such as the keyboard, mouse, and monitor). 2 Reconnect the modem/telephone cable. 3 Turn on the PC and all peripherals. 4 If you installed an add-in card, install any software drivers supplied by the card manufacturer. removing the side panel 1 See "before opening the pc" on page 104. 2 Loosen the two thumbscrews on the right side of the back panel. The first time you loosen these screws, you may need to use a Phillips screwdriver. These screws do not detach; they stay on the side panel loosely until you tighten them again. 3 Pull the panel back toward you until it stops. Lift the panel off the chassis and set it aside. NOTE: You do not need to remove the other side panel to replace the hardware listed in this guide. upgrading and servicing the pc (1) 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
upgrading and servicing the pc (1)
105
after closing the pc
To avoid injury and equipment damage, always follow this procedure in this
order after closing the PC:
1
Reconnect the power cord and all other attached cables (such as the keyboard,
mouse, and monitor).
2
Reconnect the modem/telephone cable.
3
Turn on the PC and all peripherals.
4
If you installed an add-in card, install any software drivers supplied by the
card manufacturer.
removing the side panel
1
See “before opening the pc” on page 104.
2
Loosen the two thumbscrews on the right side of the back panel. The first
time you loosen these screws, you may need to use a Phillips screwdriver.
These screws do not detach; they stay on the side panel loosely until you
tighten them again.
3
Pull the panel back toward you until it stops. Lift the panel off the chassis and
set it aside.
NOTE:
You do not need to remove the other side panel to replace the hardware
listed in this guide.