HP Pavilion xv900 HP Pavilion Desktop PCs - DVDRW - (English) Technical Suppor - Page 19

Connector and Jumpers on hp dvd-writer dvd100i Drive

Page 19 highlights

Product Information Drive Operation Troubleshooting Drive Specifications Tips and Techniques Warranty and Support Interfaces Software Release Notes Installation and Configuration Maintenance Discontinued Products Connector and Jumpers on hp dvd-writer dvd100i Drive Back of Drive DIGITAL ANALOG AUDIO AUDIO OUT OUT D G R GND L CABLE SELECT SLAVE MASTER IDE CONNECTOR DC INPUT PIN #1 5V GND 12V Signal Connector The signal connection on the hp dvd-writer dvd100i drive is a 40-pin header connector with a key slotted shroud. Additionally pin 20 has been removed from the connector for keying as shown in Figure 6.     Figure 4 Back of Internal IDE Drive Power Connector The hp dvd-writer dvd100i drive is an internal drive. The drive shares power from the PC power supply. The drive has an industry standard 4-pin Amphenol or compatible male power connector, capable of housing 18 AWG wires for each connector pin.    Pin DC Volts 1 +12 V 2 GND 3 GND 4 +5 V Missing Pin 20 (key pin) Figure 6 Interface Connector The cable is a 40 conductor (stranded 28 AWG) flat ribbon cable with female header type connectors. The maximum cable length is 18 inches. The female header type connectors that connect to the drive has a plastic extrusion on the side of the connector by pins 19 and 21. This allows the cable to correctly mate with the key slotted shroud connector on the drive. Table 12 on page 20 gives a list of the signals and connector pinout required for an ATA-2 interface. The signals listed in Table 12 are shown as single-ended contact assignments and not differential. Figure 5 DC Power Connector hp dvd-writer dvd100i Technical Support Solutions Guide 10/25/01 Physical Specifications ⇐ ⇒ 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104

hp dvd-writer
hp dvd-writer
hp dvd-writer
hp dvd-writer
dvd100i
dvd100i
dvd100i
dvd100i
Technical Support Solutions Guide 10/25/01
Physical Specifications
19
19
19
19
Connector and Jumpers on hp dvd-writer dvd100i Drive
Back of Drive
Back of Drive
Back of Drive
Back of Drive
Figure 4
Figure 4
Figure 4
Figure 4
Back of Internal IDE Drive
Power Connector
Power Connector
Power Connector
Power Connector
The hp dvd-writer dvd100i drive is an internal drive. The drive shares power from the
PC power supply. The drive has an industry standard 4-pin Amphenol or compatible
male power connector, capable of housing 18 AWG wires for each connector pin.
Figure 5
Figure 5
Figure 5
Figure 5
DC Power Connector
Signal Connector
Signal Connector
Signal Connector
Signal Connector
The signal connection on the hp dvd-writer dvd100i drive is a 40-pin header
connector with a key slotted shroud. Additionally pin 20 has been removed from the
connector for keying as shown in
Figure 6
.
Figure 6
Figure 6
Figure 6
Figure 6
Interface Connector
The cable is a 40 conductor (stranded 28 AWG) flat ribbon cable with female header
type connectors. The maximum cable length is 18 inches. The female header type
connectors that connect to the drive has a plastic extrusion on the side of the
connector by pins 19 and 21. This allows the cable to correctly mate with the key
slotted shroud connector on the drive.
Table 12
on page
20
gives a list of the signals and connector pinout required for an
ATA-2 interface. The signals listed in
Table 12
are shown as single-ended contact
assignments and not differential.
DIGITAL
AUDIO
R GND L
PIN
#
1
DC INPUT
IDE
CONNECTOR
5V
GND
12V
CABLE SELECT
SLAVE
MASTER
ANALOG
AUDIO
OUT
D G
OUT
±
²
³
´
Pin
DC Volts
1
2
3
4
+12 V
GND
GND
+5 V
´µ
³¶
²
±
Missing Pin 20 (key pin)
Product Information
Drive Specifications
Interfaces
Installation and Configuration
Drive Operation
Tips and Techniques
Software
Maintenance
Troubleshooting
Warranty and Support
Release Notes
Discontinued Products