HP Photosmart R707 HP Photosmart R707 digital camera with HP Instant Share - U - Page 119

USB Configuration - digital camera software

Page 119 highlights

1 In the Setup Menu (page 115), select Date & Time. 2 In the Date & Time sub-menu, adjust the value of the highlighted selection by using the buttons. 3 Press the buttons to move to the other selections. 4 Repeat steps 2 and 3 until the correct date/time format, date, and time are set. 5 Press Menu/OK to save the setting and return to the Setup Menu. The new setting remains in effect until it is changed again, even when you turn the camera off. USB Configuration This setting determines how the camera is recognized when connected to a computer. 1 In the Setup Menu (page 115), select USB. 2 In the USB Configuration sub-menu, highlight one of these two choices: • Digital Camera-Causes the computer to recognize the camera as a digital camera using the Picture Transfer Protocol (PTP) standard. This is the default setting on the camera. • Disk Drive-Causes the computer to recognize the camera as a disk drive using the Mass Storage Device Class (MSDC) standard. Use this setting to transfer images to a computer that does not have the HP Image Zone software installed on it (see Transferring Images to a Computer without HP Image Zone Software on page 126). This setting may not work with a Chapter 6: Using the Setup Menu 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191

Chapter 6: Using the Setup Menu
119
1
In the
Setup Menu
(page 115), select
Date & Time
.
2
In the
Date & Time
sub-menu,
adjust the value of the highlighted
selection by using the
buttons.
3
Press the
buttons to move to
the other selections.
4
Repeat steps 2 and 3 until the
correct date/time format, date, and time are set.
5
Press
Menu/OK
to save the setting and return to the
Setup
Menu
.
The new setting remains in effect until it is changed again, even
when you turn the camera off.
USB Configuration
This setting determines how the camera is recognized when
connected to a computer.
1
In the
Setup Menu
(page 115),
select
USB
.
2
In the
USB Configuration
sub-menu, highlight one of these
two choices:
°
Digital Camera
±Causes the
computer to recognize the camera
as a digital camera using the Picture Transfer Protocol (PTP)
standard. This is the default setting on the camera.
°
Disk Drive
±Causes the computer to recognize the camera as a
disk drive using the Mass Storage Device Class (MSDC)
standard. Use this setting to transfer images to a computer that
does not have the HP Image Zone software installed on it (see
Transferring Images to a Computer without HP Image Zone
Software on page 126
). This setting may not work with a