HP ProLiant ML10 HP ROM-Based Setup Utility User Guide - Page 208

Boot Disk Test, Auto-Configuration Process

Get HP ProLiant ML10 PDF manuals and user guides View all HP ProLiant ML10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 208 highlights

Boot Disk Test The boot disk diagnostic test verifies the presence and readiness of a primary boot controller. If a controller is present and ready, the test checks for a valid operating system boot sector. To run the Boot Disk diagnostic test, select Boot Disk Test from the Diagnostics Utility menu. Auto-Configuration Process The auto-configuration process automatically runs when you boot the server for the first time. During the power-up sequence, in many cases the system ROM automatically configures the entire system without needing any intervention. During this process, the ORCA Utility, in most cases, automatically configures the array with a default setting based on the number of drives connected to the server. Drives installed 1 2 3, 4, 5, or 6 More than 6 Drives used 1 2 3, 4, 5, or 6 0 RAID level RAID 0 RAID 1 RAID 5 None NOTE: If the boot drive contains logical volumes, or if more than six drives are installed on the system, ORCA does not automatically configure the array. If this occurs, you must run ORCA to configure the array settings. By default, the auto-configuration process configures the system for a default operating system. To change any default settings in the auto-configuration process, such as the settings for language, operating system, and primary boot controller, open the RBSU by pressing the F9 key after system POST. After the settings are selected according to your preference, exit RBSU and reboot the server. 208 ROM-based utilities

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
Boot Disk Test
The boot disk diagnostic test verifies the presence and readiness of a primary boot controller. If a
controller is present and ready, the test checks for a valid operating system boot sector.
To run the Boot Disk diagnostic test, select
Boot Disk Test
from the Diagnostics Utility menu.
Auto-Configuration Process
The auto-configuration process automatically runs when you boot the server for the first time. During
the power-up sequence, in many cases the system ROM automatically configures the entire system
without needing any intervention. During this process, the ORCA Utility, in most cases, automatically
configures the array with a default setting based on the number of drives connected to the server.
RAID level
Drives used
Drives installed
RAID 0
1
1
RAID 1
2
2
RAID 5
3, 4, 5, or 6
3, 4, 5, or 6
None
0
More than 6
NOTE:
If the boot drive contains logical volumes, or if more than six drives are installed on the
system, ORCA does not automatically configure the array. If this occurs, you must run ORCA to
configure the array settings.
By default, the auto-configuration process configures the system for a default operating system. To
change any default settings in the auto-configuration process, such as the settings for language,
operating system, and primary boot controller, open the RBSU by pressing the
F9
key after system
POST. After the settings are selected according to your preference, exit RBSU and reboot the server.
208
ROM-based utilities