HP ProLiant SL4545 HP Scripting Toolkit 9.30 for Windows User Guide - Page 46

HPLPCFG command-line examples, Using LO100CFG, LO100CFG command-line syntax

Get HP ProLiant SL4545 PDF manuals and user guides View all HP ProLiant SL4545 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Value 5 6 7 8 0x10 0x11 0xFF Meaning There was no adapter or Emulex HBA found on this host. There was an error retrieving the I/O address. The WWID was invalid because of one of the following: • An invalid value for WWID and BootDeviceWWID, and not a hex value • The WWID specified for HBA in the .ini file does not match any HBAs found on the host (for the /l option only) The LUN was invalid. Invalid value; for enable/disable value is not 0 or 1 (for /l option only) Incorrect iboot BIOS code loaded (for /l option only) General error: • Initialization error (for both /l and /s option) • Cannot read HBAs WWPN (for /s option only) HPLPCFG command-line examples hplpcfg /s hba.ini generates hba.ini with the following content: [HBA0] WWID=11111111 HostAdapterBiosEnable=1 SelectBootEnable=1 BootDeviceWWID= BootDeviceLUN[0]= You must edit hba.ini and add the following boot device information: [HBA0] WWID=11111111 HostAdapterBiosEnable=1 SelectBootEnable=1 BootDeviceWWID=22222222 BootDeviceLUN[0]=3 You must then invoke the tool to load the contents of hba.ini input to the HBA NVRAM: hplpcfg /l hba.ini. Using LO100CFG NOTE: This section applies only to HP ProLiant servers not using the Oxx ROM family. LO100CFG enables you to configure the LightsOut 100 device that is available on the HP ProLiant 100 series servers. Under Windows, WMI is used through the Microsoft_IPMI class, make sure WMI is installed in the Windows PE environment. LO100CFG command-line syntax lo100cfg [ -h | -x | -v | -i "file.xml" | -o "file.xml" | -s ] 46 Scripting Toolkit utilities

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Meaning
Value
There was no adapter or Emulex HBA found on this host.
5
There was an error retrieving the I/O address.
6
The WWID was invalid because of one of the following:
7
•
An invalid value for WWID and BootDeviceWWID, and not a hex value
•
The WWID specified for HBA in the .ini file does not match any HBAs found on the host (for the
/l option only)
The LUN was invalid.
8
Invalid value; for enable/disable value is not 0 or 1 (for /l option only)
0x10
Incorrect iboot BIOS code loaded (for /l option only)
0x11
General error:
0xFF
•
Initialization error (for both /l and /s option)
•
Cannot read HBAs WWPN (for /s option only)
HPLPCFG command-line examples
hplpcfg /s hba.ini generates hba.ini with the following content:
[HBA0]
WWID=11111111
HostAdapterBiosEnable=1
SelectBootEnable=1
BootDeviceWWID=
BootDeviceLUN[0]=
You must edit hba.ini and add the following boot device information:
[HBA0]
WWID=11111111
HostAdapterBiosEnable=1
SelectBootEnable=1
BootDeviceWWID=22222222
BootDeviceLUN[0]=3
You must then invoke the tool to load the contents of hba.ini input to the HBA NVRAM: hplpcfg /l
hba.ini.
Using LO100CFG
NOTE:
This section applies only to HP ProLiant servers not using the Oxx ROM family.
LO100CFG enables you to configure the LightsOut 100 device that is available on the HP ProLiant
100 series servers.
Under Windows, WMI is used through the Microsoft_IPMI class, make sure WMI is installed in
the Windows PE environment.
LO100CFG command-line syntax
lo100cfg [ -h | -x | -v | -i "file.xml" | -o "file.xml" | -s ]
46
Scripting Toolkit utilities