HP Scitex FB500 HP Scitex FB500 and FB700 Printer Series - User Cleaning Instr - Page 12

Re-install the service-end lamp housing, Clean the rail encoder strip (bi-weekly) - printer ink

Get HP Scitex FB500 PDF manuals and user guides View all HP Scitex FB500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Figure 11 Squeeze the sides of the lamp base Once the lamp housing is installed into the lamp base, tighten the four screws that you loosened in the previous step. 2. Install the two screws that secure the lamp housing to the carriage cover (see screws B in Figure 3 User end screws on page 5 for locations). 3. Connect the auxiliary cable to the top of the lamp. See Figure 1 Disconnect the user-end auxiliary cable on page 4 for location. 4. Connect the lamp power cable to the side of the lamp. See Figure 2 Remove the user-end power cable on page 4 for location. Re-install the service-end lamp housing 1. Secure the lamp housing to the lamp assembly using the original two silver screws on the service end of the carriage (see screws A in Figure 4 Service end screws on page 6 for locations). If you have difficultly fitting the lamp housing back onto the lamp base, see "Installing the UserEnd Carriage Lamp" 2. Install the two output-side screws (see screws B in Figure 4 Service end screws on page 6 for locations). 3. Connect the auxiliary cable to the top of the lamp. See Figure 1 Disconnect the user-end auxiliary cable on page 4 for location. 4. Connect the lamp power cable to the side of the lamp. See Figure 2 Remove the user-end power cable on page 4 for location. 5. Power up the printer. Clean the rail encoder strip (bi-weekly) Ink dust and debris can accumulate on the encoder strip and block accurate reading of the encoder marks by the carriage encoder reader. 10 User cleaning ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
Figure 11
Squeeze the sides of the lamp base
Once the lamp housing is installed into the lamp base, tighten the four screws that you loosened
in the previous step.
2.
Install the two screws that secure the lamp housing to the carriage cover (see screws B in
Figure
3
User end screws
on page
5
for locations).
3.
Connect the auxiliary cable to the top of the lamp. See
Figure
1
Disconnect the user-end
auxiliary cable
on page
4
for location.
4.
Connect the lamp power cable to the side of the lamp. See
Figure
2
Remove the user-end
power cable
on page
4
for location.
Re-install the service-end lamp housing
1.
Secure the lamp housing to the lamp assembly using the original two silver screws on the
service end of the carriage (see screws A in
Figure
4
Service end screws
on page
6
for
locations).
If you have difficultly fitting the lamp housing back onto the lamp base, see “Installing the User-
End Carriage Lamp”
2.
Install the two output-side screws (see screws B in
Figure
4
Service end screws
on page
6
for
locations).
3.
Connect the auxiliary cable to the top of the lamp. See
Figure
1
Disconnect the user-end
auxiliary cable
on page
4
for location.
4.
Connect the lamp power cable to the side of the lamp. See
Figure
2
Remove the user-end
power cable
on page
4
for location.
5.
Power up the printer.
Clean the rail encoder strip (bi-weekly)
Ink dust and debris can accumulate on the encoder strip and block accurate reading of the encoder
marks by the carriage encoder reader.
10
User cleaning
ENWW