HP Server tc3100 HP Surestore Drive Rail Mounting Kit Information
HP Server tc3100 Manual
 |
View all HP Server tc3100 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Server tc3100 manual content summary:
- HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 1
product updates. Configuration Guidelines HP Server tc3100 Configuration The HP Server tc3100 can accept either of the following HP Surestore tape drives: Table 1. HP Surestore Tape Drives for the HP Server tc3100 Drive DAT 24i Part No. C1555D Size Half Height Supported Location P2, R2 DAT - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 2
pressure to middle of rail Wire Rod Insert this wire rod end last Figure 2. Plastic Drive Rails HP Server tc4100 Configuration The HP Server tc4100 can accept any of the following HP Surestore tape drives: NOTE In any of these server configurations, the CD-ROM is normally mounted in location - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 3
2. HP Surestore Tape Drives for the HP Server tc4100 Drive DAT 24i DAT 40i DAT 40x6i Part No. C1555D C5686A C5716A DAT 24X6i C5677B Ultrium 230i C7400A DLT VS80i C7504A Ultrium 215i C7420A Size Half Height Half Height Full Height Full Height Full Height Half Height Half Height Supported - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 4
for attaching the metal rails to each HP Surestore tape drive. See Figure 5 for the mounting slot location. To install the metal drive rails: 1. Align the drive rail over the tape drive screw holes. 2. Secure the drive rail with the appropriate screws for the tape drive (see Table 3.). NOTE Do not - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 5
assembly in the server. The power protection bracket is located behind the non-hot swap drive cage. Before installing the C7504A or C7420A tape drive, refer to your HP Server Operations and Maintenance Guide to power down and open the server. To remove the power protection bracket: 1. If the - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 6
assembly. Remove the power protection bracket and screw from the server. NOTE The power protection bracket and screw should be saved for reinstallation if the tape drive is later removed. 6 HP Part Number 5990-3463 - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 7
drive rails on the selected tape drive and install the tape drive in the server. 7. Replace the system fan assembly and tighten the thumbscrew. 8. Close the server and replace the external cables and power cord. 9. Power up the server and return it to normal operation. HP Part Number 5990-3463 7 - HP Server tc3100 | HP Surestore Drive Rail Mounting Kit Information - Page 8
, customer responsibilities, and other terms and conditions. HP Repair and Telephone Support Refer to the Warranty & Support for your HP Server booklet supplied with your HP Server system documentation for instructions on how to obtain HP repair and telephone support. 8 HP Part Number 5990-3463
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
HP Part Number 5990-3463, Doc # 5990-3463-1
.'"&&±(°!#°'
Revised July 2002
HP Surestore Drive Rail Mounting Kit
This document includes steps to install drive rails on HP Surestore internal tape drives for installation in HP Servers. The
drive rail mounting kit includes two sets of drive rails and the hardware to install the drive rails on the tape drives.
Drive Rail Selection
The drive rail mounting kit includes a set of plastic drive rails (
Figure 2
) and metal drive rails (
Figure 5
) to attach the
rails to the HP Surestore tape drive.
•
Plastic drive rails are always used in mounting the DAT 24i and DAT 40i drives in the HP Servers.
•
Metal drive rails are used in mounting all other drives in the HP Servers.
The kit also includes screw sub-kits for mounting the metal drive rails to the HP Surestore tape drive. See
Table 3.
for
the screw sub-kits and mounting slot appropriate for each HP Surestore tape drive.
Tools Required (Metal Drive Rails Only)
The following tools are required to install the metal drive rails:
•
T-10 TORX
®
screwdriver
•
Number 1 Phillips
®
screwdriver
•
Posidrive
®
screwdriver
Where to Obtain Additional Installation Instructions
Complete mass storage device installation instructions can be found in both of the following sources:
•
The
HP Server Operations and Maintenance Guide,
on the
HP Server Documentation CD-ROM
shipped with your
HP server, has a complete chapter on installation.
•
The
HP Server Operations and Maintenance Guide
for your HP Server can be viewed and printed from the official
HP web site:
Refer to the web site for the latest revisions and product updates.
Configuration Guidelines
HP Server tc3100 Configuration
The HP Server tc3100 can accept either of the following HP Surestore tape drives:
Table 1. HP Surestore Tape Drives for the HP Server tc3100
Drive
Part No.
Size
Supported Location
Comments
DAT 24i
C1555D
Half Height
P2, R2
Use the plastic drive rails when installing the
drive on the tc3100 server.
DAT 40i
C5686A
Half Height
P2, R2
Use the plastic drive rails when installing the
drive on the tc3100 server.